Gfm – GT-10.0Z3 SL – User Manual

Category: Digital Camera, Film Camera, and Vintage Camera User Guides and Manuals

Download user manual for Gfm – GT-10.0Z3 SL – User Manual 
Preview: Below is a preview of the manual as extracted from the PDF file


i

iii
Precautions

y Before using the camera, please ensure that you read and understand the safety
precautions described below. Always ensure that the camera is operated correctly.
y Do not aim the camera directly into the sun or other intense light sources which
could damage your eyesight.
y Do not try to open the case of the camera or attempt to modify this camera in any
way. High-voltage internal components create the risk of electric shock when
exposed. Maintenance and repairs should be carried out only by authorized service
providers.
y Do not fire the flash too close to the eyes of animals or people, especially for young
children. Eye damage may result. In particular, remain at least one meter away from
infants when using flash.
y Keep the camera away from water and other liquids. Do not use the camera with
wet hands. Never use the camera in the rain or snow. Moisture creates the danger
of electric shock.
y Keep the camera and its accessories out of the reach of children and animals to
prevent accidents or damage to the camera.
y If you notice smoke or a strange odor coming from the camera, turn the power off
immediately. Take the camera to the nearest authorized service center for repair.
Never attempt to repair the camera on your own.
y Use only the recommended power accessories. Use of power sources not
expressly recommended for this equipment may lead to overheating, distortion of
the equipment, fire, electrical shock or other hazards.

„ FCC Compliance and Advisory
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.) this device may not cause harmful interference, and 2.) this device must accept any interference
received, including interference that may cause unsatisfactory operation.
This equipment has been tested and found to comply with the limits for a Class B peripheral, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and receiver.
y Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
y Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. When shielded interface cables have been provided with
the product or when specified additional components or accessories have elsewhere been designated to
be used with the installation of the product, they must be used in order to ensure compliance with FCC
regulations.
ii
Contents

PRECAUTIONS I
CONTENTS II
GETTING STARTED 1
USING THIS MENU 1
UNPACKING 2
PARTS OF THE CAMERA 3
INSERTING THE BATTERIES 5
LOW BATTERY INDICATOR 5
CHARGING THE BATTERY PACK 5
INSERTING THE MEMORY CARD 6
ABOUT CAMERA MEMORY 7
DCF PROTOCOL 7
SETTING THE DISPLAY LANGUAGE / DATE
& TIME 7
SETTING THE DISPLAY LANGUAGE 7
SETTING THE DATE & TIME 8
USING THE LCD MONITOR 9
REC MODE 9
PLAYBACK MODE 10
CHANGING THE LCD STA TUS 11
BASIC OPERATION 12
TURNING THE POWER ON AND OFF 12
POWER SA VING FUNCTION 12
CHANGING THE MODE 13
SWITCHING BETWEEN REC MODE AND
PLAYBACK MODE 13
SELECTING THE REC MODE 13
SELECTING THE ASM MODE 15
USING THE MENUS 16
REC MENU 16
SETUP MENU 17
BASIC RECORDING 20
RECORDING STILL IMAGES 20
USING THE Q MODE 21
SETTING IMAGE SIZE AND QUALITY 22
USING THE ZOOM FUNCTION 23
USING THE FLASH 24
USING THE MACRO 25
USING THE SELF-TIMER & BURST 26
USING THE APERTURE PRIORITY 27
USING THE SHUTTER PRIORITY 27
USING THE MANUAL EXPOSURE 28
USING THE STABILIZER 28
RECORDING MOVIE CLIPS 29
SETTING THE MOVIE SIZE 29
RECORDING AUDIO CLIPS 30
PLAYING BACK AUDIO CLIPS 30
RECORDING A VOICE MEMO 31
PLAYING BACK A VOICE MEMO 31
OTHER RECORDING FUNCTIONS 32
SETTING THE METERING 32
SETTING THE WHITE BALANCE 32
SETTING THE ISO 33
SETTING THE EXPOSURE 33
SETTING THE AEB 33
SETTING THE HIGHLIGHT 33
SETTING THE SHARPNESS 34
SETTING THE PHOTO EFFECT 34
SETTING DATE STAMP 34
SETTING FACE TRACKING 35
SETTING PHOTO FRAME 35
SETTING AF LAMP 35
PLAYBACK 36
PLAYING BACK IMAGES 36
PLAYING BACK MOVIE CLIPS 36
MAGNIFYING & TRIMMING STILL IMAGES
37
VIEWING IN THUMBNAIL 38
PLAYING A SLIDE SHOW 38
iii
DELETING FILES 39
DELETING A SINGLE FILE 39
DELETING MULTIPLE FILES 40
DELETING ALL FILES 40
PROTECTING A SINGLE FILE 41
PROTECTING ALL FILES 41
PROTECTING MULTIPLE FILES 42
EDITING IMAGES 43
ROTATING STILL IMAGES 43
CHANGING THE IMAGE SIZE 43
CHANGING THE IMAGE WITH EFFECTS 44
CHOOSING THE IMAGE WITH PHOTO
FRAME 44
COPYING THE FILES 45
SETTING THE DPOF 46
CHOOSING A STARTUP IMAGE 47
MAKING CONNECTIONS 48
CONNECTING THE CAMERA TO A TV 48
CONNECTING THE CAMERA TO A PC 49
USING THE CARD READER 49
CONNECTING THE CAMERA TO A
COMPUTER WITH THE USB CABLE 49
APPENDIX 50
ABOUT THE FOLDER & FILE NAME 50
FOLDER STRUCTURE 50
FILE NAMING 50
TROUBLESHOOTING 51
SPECIFICATIONS 52
FUNCTION A V AILABLE LIST 54
GFM GUARANTEE 60
1
Getting Started
Using This Menu
Getting Started
This section contains information you should know before using this camera.
Basic Operation
This section explains all recording features of this camera.
Basic Recording
This section explains how to record still images, movies, and audio files.
Other Recording Functions
This section explains common operations about recording images.
Playback
This section explains playback, delete, and edit functions of still images, movies and
audio files.
Making Connections
This section tells you how to connect this camera to a computer or TV.
Appendix
This section describes the troubleshooting and the camera specification.

The meanings of the symbols used in this user`s manual are explained below:
This indicates cautions that should be read before using these
functions.

This indicates the useful information when using this camera.

This indicates the reference page.
T Ti ip ps s
C Ca au ut ti io on n
2
Unpacking

Camera USB Cable AV Cable

Soft Case(*) Strap
Rechargeable Lithium-ion
Battery

Software Installation
CD-ROM
Quick Start Guide
Battery Charger &
Adaptor

y Actual accessories may be different.
y Items marked with (*) are available as optional accessories.
y Note that the shape of the charger plug depends on the area where you
purchased the camera.
y Do not swing the camera around by the strap.

C Ca au ut ti io on n
3
Parts of the Camera
1. Flash ( page 24)
2. Self-timer Lamp / AF Lamp
3. Lens
4. Microphone
5. Zoom Button ( page 23)
y Thumbnail ( page 38)
y Playback Zoom ( page
37)
6. Playback Button ( page
13)
7. Menu Button ( page 16)
8. Mode Button ( page 13)
9. ASM Button ( page 15)
y Delete Button ( page 39)
10. LCD Monitor ( page 9)
11. Flash Button ( page 24)
12. SET/DISP Button ( page
11)
13. Macro Button ( page 25)

4

14. Stabilizer
15. Shutter Button ( page 20,
29)
16. Operation Lamp
17. Power Button ( page 12)
18. Speaker

19. Strap Ring
20. Battery Cover ( page 5)
21. USB/AV Terminal ( page 19,
49)
22. Tripod Socket
5
Inserting the Batteries
The camera is powered by a rechargeable lithium-ion battery (Li-Ion 820 mAh).

Open the battery cover.
y Slide the battery cover in the
direction indicated by the
arrow.

Insert the batteries.
y Install the battery with the
terminal facing inside the
camera.

Close the battery cover.

Low Battery Indicator
A low battery indicator appears on the LCD screen when the batteries are nearly
exhausted. Batteries should be replaced promptly when the low battery indicator
appears.

Charging the Battery Pack
The battery is not charged when you purchase the camera. You need to charge the
battery before using the camera

Place the battery pack in the charger with
the label facing up.

Connect the AC adaptor to the charger,
and then plug it into a power outlet.
y The charger lamp lights red and battery
charging begins. When charging is
completed, the lamp becomes green.

1
2
3
1
2
6

y Risk of explosion if battery is replaced by an incorrect type dispose of used
batteries according to the instructions.
y Be sure to turn off the camera power before insert or removing batteries.
y Remove batteries if you will not be using them for a long time.
y The camera body may feel warm after extended use. This is normal.
y Use only the special rechargeable lithium-ion battery to power this camera.
y Charging time is variable with current battery capacity and charging conditions.

Inserting the Memory Card
You can use SD Card with this digital camera. The memory card slot is located beneath
the battery cover, adjacent to the battery compartment.

Open the battery cover.
y Slide the battery cover in the
direction indicated by the
arrow.

Insert the card.
y Insert the card with the label
facing the battery pack and the
arrow pointing in.

y To remove the card, gently press on the edge of the card and release it. Pull
the card out and close the battery cover.

Close the battery cover.

y It may cause damage to the card if removed while the camera is on.
y Do not touch the connection terminals on the back side of the card.

1
2
3
C Ca au ut ti io on n
T Ti ip ps s
C Ca au ut ti io on n
7

About Camera Memory
This camera is equipped with internal memory. If the memory card is not inserted in the
camera, all images and movie clips recorded by the camera will be stored in the internal
memory. If the memory card is inserted, images and movie clips are stored on the
memory card.
DCF Protocol
The DCF protocol defines the format for image file data as well as the directory structure
for the memory card. Images that are taken by a DCF camera can be viewed on
DCF-compatible cameras from other manufacturers.

Setting the Display Language / Date & Time
When using the camera for the first time after purchasing, be sure to choose a language
and set the date & time before using the camera.
Setting the Display Language

Turn the power on, and set the camera
to the Setup Menu ( page 17).

Select [ Language].
y Press or to select
[LANGUAGE] then press or the
SET button to launch the submenu.

Select a language.
y Press or to select a language and press or the SET button to
apply the setting.

Press the MENU button to close the menu.

1
3
2
4
8

Setting the Date & Time

Turn the power on, and set the camera
to the Setup Menu ( page 17).

Select [ Date & Time].
y Press or to select [Date &
Time] then press or the SET
button to launch the submenu.

Set date and time.
y Press or to change the value of the cursor located. Press or
to move the cursor between settings.

y Holding down or changes the values continuously.
y For date stamp setting ( page 34).

Apply the setting.
y After adjusting the settings, press the SET or the MENU button to apply the
setting.

y If the batteries are removed for longer than 48 hours, the Date and Time will
need to be re-set.

1
2
3
4
T Ti ip ps s
C Ca au ut ti io on n
9
Using the LCD Monitor
The LCD monitor is used to compose images while recording, adjust settings and replay
images. The following indicators may appear on the LCD monitor while recording or
playing back images.
REC mode
1 Recording mode ( page 13) 14 Shutter speed ( page 20)
2 Flash ( page 24) 15 Shake warning ( page 20)
3 Macro ( page 25) 16 Aperture value ( page 20)
4 Self-timer / Burst ( page 26) 17 Face tracking ( page 35 )
5 Zoom indicator ( page 23) 18 Exposure ( page 33)
6 Shots remaining 19 Focus area ( page 20)
7 Battery ( page 5) 20 Date stamp ( page 34)
8 Storage media 21 AEB ( page 33)
9 Stabilizer 22 Sharpness ( page 34)
10 Metering ( page 32) 23 Quality ( page 22)
11 ISO ( page 33) 24 Resolution ( page 22)
12 Histogram 25 AF Lamp( page 35)
13 White balance ( page 32)

10

PLAYBACK mode
1 Playback mode ( page 13) 7 Recording info ( page 11)
2 Protect ( page 41) 8 Histogram
3 Voice memo ( page 31) 9 Captured date & time
4 File number / Total 10 Voice memo control ( page 31)
5 Battery ( page 5) 11 DPOF ( page 46)
6 Storage media 12 Resolution ( page 22)

y Some information may not display correctly if you display images captured by
other camera model.

C Ca au ut ti io on n
11

Changing the LCD Status
Press the SET/DISP button changes the LCD status as shown below:
„ REC mode

(A) OSD on (B) Full OSD (C) Guide line (D) OSD off

y Use the “Guide line” to compose images easily before shooting images.
„ PLAYBACK mode

(A) OSD on (B) Full OSD (D) OSD off

y You cannot change the LCD status in the following situation:
。 Manual exposure
。 Recording movie clips or audio files
。 Playing movie clips or audio files
。 Playing the slideshow
。 Viewing in thumbnail
。 Trimming a still image

T Ti ip ps s
C Ca au ut ti io on n
12
Basic Operation
Turning the Power On and Off

Press the POWER button ( n ) to turn on
the camera in the REC mode.
y The power turns on, the lens extends
and the LED lights in green.

Press the PLAYBACK button ( o ) to turn
on the camera in the PLAYBACK mode.
y The power turns on, and an image
displays on the LCD monitor ( p ).

Press the POWER button ( n ) again to turn the power off.
y The power turns off, the lens retracts and the LED turns off.

y You can turn on the camera without the start-up and operating sound by
pressing and holding the POWER ( n ) or the PLAYBACK ( o ) button over 1.5
seconds.
y Switch between REC mode and PLAYBACK mode ( page 13).

Power Saving Function
For saving the battery power, the LCD monitor automatically turns off 1 minute after the
last control accessed (factory-preset setting). Press any button other than the power
button to turn on the LCD monitor. You can change the power save setting in Setup
menu ( page 18).

After the power saving function has been active for 1 minute, the power will turn off
completely. Press the POWER ( n ) or the PLAYBACK ( o ) button to restore the power.

The power save feature will not activate in the following situation:
y Recording movie clips or audio files
y Playing movie clips or audio files
y Playing the slideshow
y Connecting the camera to a computer or printer with the USB cable
1
2
T Ti ip ps s
13
Changing the Mode
You can record images and voices in the REC mode. And using the PLAYBACK mode to
replay, delete, or edit images on the LCD monitor.
Switching between REC mode and PLAYBACK mode
In REC mode, press the PLAYBACK button
( n ) to switch to the PLAY mode.

In PLAY mode, press the PLAYBACK ( n )
or the MODE ( o ) button to switch to the
REC mode.

Selecting the REC mode

Set the camera to the REC mode
( page 13).

Launch the mode palette.
y Press the MODE button ( o ) to
show the scene mode palette.

Select a mode.
y Use the four-way control to select a desired mode and press the SET
button to confirm the setting.

Display Title Description

Program The camera makes settings suitable for the shooting conditions.

Movie For recording movie clips.

Voice REC For recording audio.

Q Mode Allows beginners to take pictures easily.

Portrait Blurring the background to focus on the subject.

Landscape Used for the wide scenic views.
1
3
2
14
Display Title Description

Sunset Enhance the red hue for recording sunset images.

Backlight Shooting the image of backlight object by changing metering.

Night Scene Shooting the subject while keeping the background night scenery.

Sports Used to take still pictures in high speed motions.

Party Used for the wedding or indoor parties.

Snow Used for the beach or snow scenes.

Kids Take a still image to capture moving kids.

Candlelight To capture the warmth effects of candle light.

Fireworks Slow shutter speed to take fireworks exploding.

Night
Portrait
Use to take portrait pictures when the background is darker.

Soft Skin Enhance the tone of skin so that the facial skin appears smooth.

Soft Flowing
Water
Can take pictures with effects as smooth as silk.

Food Higher saturation makes food more appetizing.

Building Enhance the edges of the subject.

Text Enhance the black & white contrast.

15

Selecting the ASM mode

Set the camera to the REC mode
( page 13).
y It cannot be switch to ASM mode
while in Movie or Voice REC mode.

Launch the ASM mode.
y Press the ASM button ( n ) to toggle
switch between Aperture Priority,
Shutter Priority, Manual Exposure
mode.
y For detail operation ( page26).

1
2
16
Using the Menus
When a menu is displayed, the four-way control and the SET button are used to make
the desired settings.
REC menu

Turn the power on, and set the
camera to the REC mode
( page 13).

Open the REC menu.
y Press the MENU button ( n ) to
display the menu.

Select an item.
y Press or ( o ) to select a menu item.

Change the setting.
y Press or ( o ) to change the setting.

Press the MENU ( n ) or the SET ( o ) button to save the settings and close
the menu.

REC menu list (Still Image)
Menu Item Available Setting Page
Resolution
/ / / / / /
22
Quality / / 22
Metering / / 32
White Balance
Auto / / / / / /
32
ISO
Auto / ISO50 / ISO100 / ISO200 / ISO400 /
ISO800 / ISO1600
33
Exposure … 33
Drive Mode Off / / / / 26
AEB Off / 33
Highlight Off / / / 33
Sharpness / / 34
Effect
Off / B&W / Sepia / Negative / Red / Green / Blue
34
4
5
1
2
3
17
Date Stamp Off / Date / Date & Time 34
Digital Zoom Off / On 23
Face Tracking Off / On 35
Photo Frame Off / Frame 1 ~ 10 35
AF Lamp Auto / Off 35

REC menu list (Movie)
Menu Item Available Setting Page
Movie Size
/ /
29
Metering
/ /
32
White Balance
Auto / / / / / /
32

Setup menu

Turn the power on, and set the
camera to the REC or
PLAYBACK mode ( page 13).

Press the MENU button ( n ) to
open the REC or PLAYBACK
menu.
y The menu displays depends
on whether you are in the REC
mode or the PLAY- BACK
mode.

Open the Setup menu.
y Press four-way control ( o ) to select SETUP ( ) and then press the SET ( o )
button to display the Setup menu.

Select an item.
y Press or ( o ) to select a menu item and then press or the SET ( o )
button to launch the submenu.

Change the setting.
y Press or ( o ) to select an option and press or the SET ( o ) button to
apply the setting.
3
4
5
1
2
18

Press the MENU ( n ) button to close the menu.

Setup menu list
Menu Item Functions
Sounds
[Shutter]:
[Start-up]:
[Beep]:
[Volume]:
Sets the shutter sound on and off.
Sets a type of the start-up sound.
Sets the operation sound on and off.
Adjusts the volume of the shutter sound, start-up
sound, beep and playback sound.
Auto Review
[Off]:

[3 sec.]:

[5 sec.]:
The captured image will not automatically display after
shooing.
The captured image will display for 3 seconds after
shooting.
The captured image will display for 5 seconds after
shooting.
Power Save
[1 min.] / [3 min.] / [5 min.]:
For power consumption, the camera is turned off automatically
for a period of time.
y The power save feature will not activate in some situation
( page 12).
Date & Time Sets the date & time ( page 8).
Select a language for display menus and other information from
the following 21 languages: ( page 7)
Language
[English]: English
[Deutsch]: German
[Italiano]: Italian
[Nederlands]: Dutch
[Magyar]: Hungarian
[Türk]: Turkish
[Svenska]: Swedish
[Rumänisch]:Romanian
[ ﻲﺑﺮ ﻋ ]: Arabic
[ไท ย ]:Thai
[한국 어]: Korean
[繁體中文]: T. Chinese
[Español]: Spanish
[Français]: French
[Português]: Portuguese
[ Čestina]: Czech
[Polski]: Polish
[Ру сский]: Russian
[ Ελληνι κ ά]: Greek
[日本語]: Japanese
[简体中文]: S. Chinese

Use this function if the camera experiences a “Folder cannot be
created” error or if you want to restart numbering, for example,
after erasing all files.
File No.
[Series]: Store the latest used file number no matter deleting
6
19
Menu Item Functions

[Reset]:
files or inserting a new memory card.
Reset file numbering each time the memory card is
changed.
y Resetting the file number is useful for avoiding the file name
duplication when images are downloaded to a computer
( page 50).
You can review images on a television with a supplied AV cable
( page 48). TV Out should be set to either NTSC or PAL
depending on your region. TV Out
[NTSC]:
[PAL]:
America, Japan and others
Europe, Oceania and others
USB
[Computer] / [Printer]:
Sets the USB mode to connect the camera with a printer or
computer ( page 49).
S.Image Sets a recorded image as the start-up image ( page 47).
Format
To erase all data stored in the memory card if you are using a
card, or all data stored in the internal memory if there is no card
inserted.
y A “BUSY…PLEASE WAIT” message displays and the
memory card is starting format.
y A “COMPLETED” message displays when finish formatting.
y All data will be deleted including protected files. Be sure to
download important files to your computer before formatting.
Reset All
Resets the entire menu and button operation settings to initial
default.
The following settings do not change after Reset All:
y Date & Time setting
y Language setting
y TV out setting

20
Basic Recording
Recording Still Images

Turn the power on, and set the
camera to the REC mode
( page 13).

Compose the subject on the
monitor.
y Aim the focus area ( n ) to the
subject that you want to take.

Half press the shutter button to focus the image.
y The focus area ( n ) becomes green while in focus, then shutter speed ( o ),
aperture value ( p ) and ISO value ( q ) are displayed.
y If the shutter speed is slow or the possibility that image may be blurred, the
shake warning icon may appear on the LCD monitor. To avoid this, use a
tripod to stabilize the camera when recording images.

Take a picture.
y Press the shutter button fully to
take a picture.

y Make sure that your fingers or
the wrist strap does not block the
lens.

3
4
1
2
C Ca au ut ti io on n
21

Using the Q mode
The Q mode provides a simplified camera
interface. Larger icons and fewer controls
make it easier to take pictures anytime,
especially for the beginners and elder users.

You can use only the basic settings in the Q
mode:

Flash: Auto / Red eye / Force on / Slow sync / Force off
Macro: Off / On
SET/DISP: OSD on / Guide line / OSD off
Button
Stabilizer: Off / On
Resolution: 10M / 3:2 / 16:9 / 8M / 5M / 3M / VGA
Drive Mode: Off / 2 sec. / 10 sec. / Double / Burst
Face Tracking: Off / On
Photo Frame: 10 frames can be selected
Beep: Off / On
Menu
Auto Review: Off / 3 sec. / 5 sec.

Rest of settings will not be controlled as below:
y Quality: S.Fine y Highlight: Off
y Metering: Multi y Sharpness: Normal
y White balance: Auto y Effect: Off
y ISO: Auto y Date Stamp: Date & Time
y Exposure: Auto y Digital Zoom: Off
Fixed setting
(*)
y AEB: Off y AF lamp: Auto
y Shutter sound y File No.
y Start-up sound y TV out
y Power save y USB
y Date & Time y Start-up image
Utility setting
(**)
y Language
(*)Fixed setting: Settings are fixed in Q mode.
(**)Utility setting: Use the same setting as last mode used.

22

Setting Image Size and Quality
You can select lower image resolution and quality to decrease the image size to capture
more images. Choose a suitable setting according to the desired image quality and
purpose. For details, see page 16.

Resolution Values
Image Size Print Size

3584 x 2688 Printing larger than A4-size.

3648 x 2432

3584 x 2016

3328 x 2496

2560 x 1920

2048 x 1536

640×480 Printing to postcards or attaching to e-mail.
Larger

Smaller

Quality Values
Compression Purpose

Super Fine Shoot higher quality images.

Fine Shoot normal quality images.

Normal Shoot for more images.
Higher Quality

Lower Quality

23

Using the Zoom Function
Your camera has a combination of optical and digital zoom functions that allows you to
zoom in on far away subjects or zoom out for a wide angle shot.

The optical zoom is achieved by mechanically adjusting the lens of the camera. The
digital zoom enlarges or shrinks the image using a software process.

Select the zoom setting, and
point the camera at the subject.

Press the zoom button ( n ) to
compose the image.
[W]: zoom out for a wide-angle
shot.
[T]: zoom in for a telephoto shot.
y When the zoom button is
pressed, the zoom bar appears
on the LCD monitor.
y When the optical zoom ( o )
factor is at maximum, zooming
stops temporarily. Press the
[T] again, the camera switches
to the digital zoom ( p )
automatically and zooming
continues.
y The digital zoom ( p ) will not
activate in movie recording.

Press shutter button to take a
picture.

y Digital zoom works by enlarging the center portion of an image through a
software interpolation process.
y The digital zoom is used to achieve magnification levels up to approx. 4 times.

1
2
3
T Ti ip ps s
24

Using the Flash
The flash is not only for taking pictures when there is insufficient light, but also when the
subject is in shade or in backlight conditions. Press the flash button to cycle your camera
through the various flash modes. The flash will not activate when continuous shooting or
movie recording.

Turn the power on, and set the camera
to the REC mode ( page 13).

Press the flash button ( n ) to change
the flash mode.
y Each time the flash button is
pressed, the flash icon ( o ) changes.

Auto flash:

Flash fires automatically when
shooting conditions require extra
lighting.

Red-eye reduction:

Flash strobes to let the subject’s
eyes adjust to the flash, then
fires again to take the actual
image. Your camera will detect
the subject brightness and use
the flash only when required.

Force on:
Flash fires every time you take a photo, regardless of lighting conditions.

Slow sync:
Flash fires with a slow shutter speed.

Force off:
The flash never fires even in dark situation.

Press shutter button to take a picture.

y The flash charging time may increase when the battery is low.
y The available flash settings are limited depending on the REC mode you selected
( page 54).
1
2
3
C Ca au ut ti io on n
25

Using the Macro
Your camera is equipped with a macro function that allows you to focus on very close
subjects. In macro mode you can focus on subjects 10 cm from the lens when in the
maximum wide angle setting and 50 cm in the maximum telephoto setting.

Turn the power on, and set the camera
to the REC mode ( page 13).

Press the macro button ( n ) enters the
macro mode.
y The macro icon ( o ) displays in the
LCD monitor.
y To leave the macro mode, press the
macro button ( n ) again.

Press shutter button to take a picture.

y Distances referred to measure the distance between the camera lens surface
and the subject.
1
2
3
T Ti ip ps s
26

Using the Self-timer & Burst
Use the self-timer to set a delay from the time the shutter button is pressed to the time
the image is shot. Use the burst to record continuous still images shooting.

Turn the power on, and set the camera
to the REC mode ( page 13).

Open the REC menu ( page 16).
y Use or to select [Drive mode]
from the REC menu.

Change the setting.
y Press or to select a drive
mode, then press the SET button.

Off:
Record a single image.

2 sec.:

The shutter release will be delay for 2 seconds.

10 sec.:
The shutter release will be delay for 10 seconds.

Double:

Record two images in a shot after pressing the shutter release button 10
and 12 seconds.

Burst:

Keep pressing the shutter button fully to take continuous shooting.
Release the shutter button to stop shooting.

Press shutter button to take a picture.

y When using the self-timer function, be sure to use a tripod or place the digital
camera on a level, stable surface.

4
1
2
3
T Ti ip ps s
27

Using the Aperture Priority
In this mode, you can set an aperture value to match the brightness. A higher aperture
value brings the background out of focus. Selecting a lower aperture value allows you to
soft the background.

Turn the power on, and set the
camera to the Aperture Priority
( page 15).

Adjust the aperture value by
pressing or button.

Press shutter button to take a
picture.

y The larger the aperture value the smaller the lens opening, allowing less light to
enter the camera.

Using the Shutter Priority
In this mode, you can set a shutter speed to match the brightness. Faster shutter speeds
allow you to take a sharp picture of a moving subject while slower speeds create a trail
effect and allow you to shoot without a flash in dark areas.

Turn the power on, and set the
camera to the Shutter Priority
( page 15).

Adjust the shutter speed by
pressing or button.

Press shutter button to take a
picture.

1
2
3
T Ti ip ps s
1
2
3
28

Using the Manual Exposure
You can manually set the shutter speed and aperture to achieve a particular effect.

Turn the power on, and set the
camera to the Manual Exposure
( page 15).

2
Use the SET button to switch
between aperture value and
shutter speed control. Press
or to adjust the setting.

Press shutter button to take a
picture.
y Press the shutter button halfway,
the difference between the
standard exposure and the
selected exposure appears in
red.

Using the Stabilizer
With more sensitivity and faster shutter speed to brighten up the pictures, this effectively
prevents blurred images caused by hand shaking or target movement.

1
3
2
29
Recording Movie Clips

Turn the power on, and set the
camera to the Movie mode
( page 13).

Compose the subject on the
monitor.
y Aim the focus area ( q ) to the
subject that you want to take.
y The LCD monitor displays the
available recording time ( p ).

Start recording.
y Press the shutter button (n ) to
start recording.
y Using the zoom button ( o ) to
adjust the image size.
y The White Balance is set and
locked to the settings of the first
frame

y Sound cannot be recorded while pressing the zoom button..
y The digital zoom cannot be used in Movie mode.

Finish recording.
y Press the shutter again to end recording.
y The camera will stop recording automatically when the memory capacity
has been reached.

Setting the Movie Size
Movie Size and Frame Rate
Resolution Frame Rate

848 x 480

640 x 480

320 x 240
30 frames/sec.
Higher Quality

Lower Quality
1
2
3
C Ca au ut ti io on n
4
30
Recording Audio Clips

Turn the power on, and set the
camera to the Voice REC mode
( page 13).

Press the shutter button to start
recording.
y The voices are recorded from
the microphone ( n ) of the
camera. Be careful to avoid
touching the microphone while
recording.

Press the shutter button again to end recording.
y The camera will stop recording automatically when the memory capacity
has been reached.

Playing Back Audio Clips

Turn the power on, and set the
camera to the PLAYBACK mode
( page 13).

Press or to select the audio
clip that you want to playback.

Start playing back.
y Press to start playing the audio clip.
y Press to stop the audio clip, or press to pause it. When audio clip
paused, press again to resume.

3
1
2
3
1
2
31
Recording a Voice Memo
You can add a voice memo to the still images after you record it.

Turn the power on, and set the camera
to the PLAYBACK mode ( page 13).

Press or to select a still image
that you want to add a voice memo.
y If the image already has the voice
memo recorded, the appears on
the LCD monitor. The new recording
will replace the previous one.

Open the PLAYBACK menu.
y Press the MENU button, using four-way control to select Voice Memo ( )
and press the SET button.

Press the SET button to start recording for 30 seconds.
y Press the SET button again to end recording.

y The voice memo cannot be added to a movie clip or a protected image.
y You cannot delete only the voice memo. When you delete the image, the
attached voice memo is also deleted.

Playing Back a Voice Memo

Turn the power on, and set the camera to the PLAY mode ( page 13).

Press or to select the image that has the voice memo recorded.

Start playing back.
y Press to start playing the voice memo.
y Press to stop the voice memo, or press to pause it. When voice
memo paused, press again to resume.

3
1
2
4
C Ca au ut ti io on n
3
2
1
32
Other Recording Functions
Setting the Metering
There are 3 different light metering options available on your camera.

Option Description

Light is measured from the entire shooting screen, but gives
more importance to the values near the center.

Selects an exposure based on readings from multiple points in
the subject area.

Selects an exposure based on a single reading taken from the
center of your picture.

Setting the White Balance
Adjust the white balance to match different light sources such as sunlight, incandescent
(tungsten) lighting or, fluorescent lighting.

Option Description

Automatically corrects white balance. Ideal for general
photography.

Adjusts for bright sun conditions, or natural light conditions.

Adjusts for cloudy days or twilight conditions.

Adjusts for normal indoor lighting conditions. Corrects the
orange hue of household light bulbs. Ideal for indoor photos
under tungsten or halogen lighting without a flash.

Adjusts for fluorescent lighting. Corrects the green hue of
fluorescent lighting. Ideal for indoor photos under fluorescent
lighting without a flash.

For more accurate adjustment or when the light source cannot
be specified.

y Point the camera at a white piece of paper or similar object under the lighting
conditions for which you want to set the white balance, and then press the
Shutter button.
T Ti ip ps s
33
Setting the ISO
With the initial settings, the ISO sensitivity is automatically set according to the
brightness of the subject.

Option Description
Auto Sets the ISO sensitivity automatically.
ISO 50 Sets the sensitivity to ISO 50 equivalent.
ISO 100 Sets the sensitivity to ISO 100 equivalent.
ISO 200 Sets the sensitivity to ISO 200 equivalent.
ISO 400 Sets the sensitivity to ISO 400 equivalent.
ISO 800 Sets the sensitivity to ISO 800 equivalent.
ISO 1600 Sets the sensitivity to ISO 1600 equivalent.

y Higher ISO speeds increase the image noise. To take clean images, use as low
an ISO speed as possible.

Setting the Exposure
Set the exposure value manually to compensate for unusual lighting conditions such as
indirect indoor lighting, dark backgrounds, and strong backlighting.

Setting the AEB
Sets the auto exposure bracketing (AEB) to shoot 3 continuous images, each with a
different exposure setting: correctly exposed, underexposed, and overexposed.

Setting the Highlight
Make the subject stand out from its surroundings. The subject will be in focus in three
different ranges: / /

T Ti ip ps s
34
Setting the Sharpness
You can select whether you want the image to have sharp or soft outlines.

Option Description

The edges of the image are emphasized. The edges will
become sharp, but noise may occur in the recording image.

The edges of the image are sharp. This is suitable for printing.

The edges of the image are softened. This is suitable for editing
images on PC.

Setting the Photo Effect
You can add special effects to your images in Record mode or in Playback mode.

Option Description
Off No effect is added to the image.
B&W Convert image to black & white.
Sepia Recorded image will be stored in a sepia tone.
Negative Opposite what they were in the original image.
Mosaic Add mosaic tiles to the images. (Playback only)
Red The image becomes reddish.
Green The image becomes greenish.
Blue The image becomes bluish.

Setting Date Stamp
The Date Stamp function can be used to add a date to your pictures as you take them.

Option Description
Off Do not add the recorded date & time to printed images.
Date Only add the recorded date to printed images.
Date & Time Add the recorded date & time to printed images.

35
Setting Face tracking
After initializing face tracking function, the lens will lock the main character in the picture
and follow the movements. Also use auto digital zoom technology to retract and extract
zoom lens that allows you to become the focus of lens.

y Pressing the shutter halfway showing green AF area means focus is complete.
y Face tracking is powered by Arcsoft.
y Under some environmental influences, face tracking function may be limited.

Setting Photo Frame
You can add 10 kinds of frames to still images, making them more interesting.

y This feature only available with still images (except 3:2 and 16:9).

Setting AF Lamp
The AF Lamp function allows you record images in low light conditions.

Option Description
Off Disable the AF lamp while recording images.
Auto
The AF lamp turns on automatically by half pressing the shutter
button under low light conditions.

T Ti ip ps s
T Ti ip ps s
36
Playback
Playing Back Images

Turn the power on, and set
the camera to the PLAYBACK
mode ( page 13).
y The latest recorded image
appears on the LCD
monitor.
y If there are no images
stored, a message [No
image] appears.

Press the four-way control or ( n ).
y : displays the previous image.
y : displays the next image.

y Holding down or scrolls images in a high speed.

Playing Back Movie Clips

Turn the power on, and set the camera to the PLAYBACK mode ( page
13).

Press or to select a movie clip that you want to playback.

Start playing back.
y Press to start playing the movie clip.
y Press to stop the movie clip, or press to pause it. When the movie
paused, press again to resume.

y During movie playing back, press to fast forward or press to rewind it.
y Press the shutter to capture the still image from the movie clip while it had paused.
3
2
1
T Ti ip ps s
1
2
T Ti ip ps s
37

Magnifying & Trimming Still Images

Turn the power on, and set the
camera to the PLAYBACK
mode ( page 13).

Select an image.
y Press or ( p ) to select
the image that you want to
magnify or trimming.
y Only still images can be
magnified and trimmed.

Magnify the image.
y Press [T] ( n ) to magnify the image, and the central portion of the image is
displayed. You can use the arrow button ( p ) to view different parts of the
magnified image.
y Press the MENU button ( o ) to return to the normal size.

Trim the image.
y Press the SET button ( p ) to set the image trimming.

Save the image.
y Press the SET button ( p ) again to trim the selected image and save it as a
new one.

3
5
4
1
2
38

Viewing in Thumbnail

Turn the power on, and set the
camera to the PLAYBACK mode
( page 13).

Press the zoom button [W], a
thumbnail screen is displayed.

Use the four-way control to select the desired image, and press [T] or the
SET button to show the selected image in full screen.

y You can protect or delete multiple images in thumbnail, see page 40, 42.

Playing a Slide Show

Turn the power on, and set the
camera to the PLAYBACK mode
( page 13).

Enter the slide show.
y Press the MENU button ( n ), use
the four-way control ( o ) to select
Slide Show ( ) and press the
SET button ( o ).

Change the slide show settings.
y Use the four-way control ( o ) to set the slideshow interval ( ), effect ( )
and repeat ( ).
y You can set the interval between 1~10 seconds.

Playing the slide show.
y Press the SET button ( o ) to start the slideshow.
y During the slideshow, press the SET button ( o ) to pause the slideshow and
press the SET button again to resume.
3
1
2
4
T Ti ip ps s
1
2
3
39
Deleting Files
Deleting a Single File

Turn the power on, and set the
camera to the PLAYBACK mode
( page 13).

Open the menu.
y Press the MENU button ( n ), then
use the four-way control ( o ) to
select Delete ( ) and press the
SET button ( o ).

Press or ( o ) to select [SINGLE], and then press the SET button ( o ).

Press or ( o ) to select the image you want to delete.

Press the SET button ( o ) to delete the image.
y Repeat step 4~5 to delete images.

y To quickly delete the current display image
1. Select the image you want to delete.
2. Press the Delete button ( p ) to show a confirmation.
3. Press the SET button ( o ) to delete the current display image.
y Protected images cannot be deleted with this function.
1
2
3
4
5
T Ti ip ps s
40

Deleting Multiple Files

Turn the power on, and set the camera to
the thumbnail screen ( page 38).

Open the menu.
y Press the MENU button, then Press
or to select to select Delete ( ) and

press the SET button.

Press or to select [Select], and then press the SET button.
y The frame of the selected image turns green.

Select multiple images.
y Use the four-way control to select the image.
y Press the SET button toggles the on and off. Repeat this step until all
images that you want to delete are displayed with an icon .

Delete images.
y Press the MENU button, then select [Yes] and press the SET button. All
selected images will be deleted.
y To cancel delete, press the MENU button in this step.
Deleting All Files

Turn the power on, and set the camera to
the PLAYBACK mode ( page 13).

Open the menu.
y Press the MENU button, then use the
four-way control to select Delete ( )

and press the SET button.
y You can open the menu in full screen or in thumbnail.

Press or to select [ALL], and then press the SET button.

Press the SET button to delete all unprotected images.
3
1
2
4
1
2
3
4
5
41

Protecting a Single File

Turn the power on, and set the camera to the PLAYBACK mode ( page
13).

Open the menu.
y Press the MENU button, then use the four-way control to select Protect
( ) and press the SET button.

Press or to select [SINGLE], and then press the SET button.

Press or to select the image you want to protect.

Press the SET button to protect the image.
y When the file is locked, the displays on the LCD monitor.
y Repeat step 4~5 to protect images.
y To unlock the file, press the SET button again in step 5. The will
disappear and the file is unlocked.

Protecting All Files

Turn the power on, and set the camera to
the PLAYBACK mode ( page 13).

Open the menu.
y Press the MENU button, then use the
four-way control to select Protect ( )
and press the SET button.
y You can open the menu in full screen or in
thumbnail.

Press or to select [Lock all], and then press the SET button.
y To unlock all files, select [Unlock all] in this step, then press the SET
button.

Press the SET button to protect all images.
1
2
3
4
5
3
1
2
4
42

Protecting Multiple Files

Turn the power on, and set the camera
to the thumbnail screen ( page 38).

Open the menu.
y Press the MENU button, then Press
or to select to select Protect
( ) and press the SET button.

Press or to select [Select], and then press the SET button.
y The frame of the selected image turns green.

Select multiple images.
y Use the four-way control to select the image.
y Press the SET button toggles the on and off. Repeat this step until all
images that you want to protect are displayed with an icon .

Protect images.
y Press the MENU button, then select [Yes] and press the SET button. All
selected images will be protected.
y To cancel protect, press the MENU button in this step.

1
2
3
4
5
43
Editing Images
Rotating Still Images

Turn the power on, and set the
camera to the PLAYBACK mode
( page 13).

Press or to select the image
you want to rotate.

Open the menu.
y Press the MENU button, then use the four-way control to select Rotate ( )
and press the SET button.

Press the SET button to rotate the image.
y Each press rotates the image 90 degrees in clockwise.

Press or to select OK, and then press the SET button to finish
rotating.

Changing the Image Size

Turn the power on, and set the camera to the PLAYBACK mode ( page
13).

Press or to select the image you want to resize.

Open the menu.
y Press the MENU button, then use the four-way control to select Resize
( ) and press the SET button.

Press or to select an option, and then press the SET button.
y The resized image will be saved as a new file.

y Only a large size image can be resize to a smaller one.
3
1
2
4
5
1
2
3
4
C Ca au ut ti io on n
44

Changing the Image with Effects

Turn the power on, and set the camera to the PLAYBACK mode ( page
13).

Press or to select the image you want to add the effect.

Open the menu.
y Press the MENU button, then use the four-way control to select Effect
( ) and press the SET button.

Press or to select an option, and then press the SET button.
y The edited image will be saved as a new file.

Choosing the Image with Photo Frame

Turn the power on, and set the camera to the PLAYBACK mode ( page
13).

Press or to select the image you want to add the photo frame.

Open the menu.
y Press the MENU button, then use the four-way control to select Photo
Fames ( ) and press the SET button.

Press or to select the image you want, then press the SET button to
apply the choice.
y The edited image will be saved as a new file.

1
2
3
4
3
4
2
1
45
Copying the Files
You may copy the data from the camera’s internal memory to the memory card for
convenience.

Be sure you have inserted a memory
card into your digital camera. Set
the camera to the PLAYBACK mode.
( page 13).

Open the menu.
y Press the MENU button, then use
the four-way control to select
Copy to card ( ) and press the
SET button.

Press or to select [Single], then press the SET button.
y To copy all images to a memory card, select [All].

Press or to select the image you want to copy to a card.

Select [Yes] and then press the SET button to start copy.
y Repeat step 4~5 to copy other images.
y Press the MENU button to complete the setting.

3
1
2
4
5
46
Setting the DPOF
The Digital Print Order Format (DPOF) setting allows you to select images on the
memory card for printing and specify the number of print copies in advance using the
camera. This is extremely convenient for sending the images to a photo developing
service or for printing on a direct print function compatible printer.

Turn the power on, and set the camera
to the PLAYBACK mode ( page 13).

Open the menu.
y Press the MENU button, then use the
four-way control to select DPOF ( )
and press the SET button.

s
Press or to select [Single], then press the SET button.
y To set the DPOF setting for all images, select [All] in this step.
y To reset all DPOF settings to initial default, select [Reset] in this step.

Press or to select the image you want to print out, then press the
SET button.

Set the number of copies.
y Press or to specify the number of copies.
y The number of copies can be set from 0 to 30.
y To cancel this image DPOF setting, set the number of copies to 0.

Print the date stamp out.
y Press and then press or to set or cancel the date stamp of
current image.
y Repeat step 4~6 to other images for printing.

Press and then press the SET button to apply the setting or press the
MENU button to cancel.

After you finished all image settings, select [ ] and press the SET
button to apply it.

3
1
2
4
5
6
7
8
47
Choosing a Startup Image

Turn the power on, and set the camera to the PLAYBACK mode ( page
13).

Open the menu.
y Press the MENU button, then use the four-way control to select S.Image
( ) and press the SET button.

Press or to select the image you want, then press the SET button to
apply the choice.
y A message “Completed” appears.

Set the camera to the Setup Menu ( page 17).

Press or to select S.Image
( ) then press or the SET
button.

Press or to select a desired
option and press the SET button to
apply the setting.

[Off]: Disable the start-up image.
[System]: Use camera default image.
[My image]: Use the image that you just specified in step 3.

Press the MENU button to close the menu.

y The start-up image will not be deleted even if the original image is deleted or
memory formatted.

3
1
2
4
5
6
7
C Ca au ut ti io on n
48
Making Connections
Connecting the Camera to a TV
You can display recorded images on a television with a supplied AV cable.

Set the TV out to match the TV system that you are using ( page 19).

Turn off the camera and the TV.

Use the supplied AV cable to connect the camera to the TV set.

Set the TV input signal to Video In.
y Refer to the documentation included with your TV for more information.

Display on TV.
y Everything that would normally appear on the camera’s LCD screen, such
as photo and video clip playback, slide shows, and image or video capture,
appears on the TV.

3
1
2
4
5
49
Connecting the Camera to a PC
There are two ways to download files from the camera’s internal memory or memory
card to a computer:
y Inserting the memory card into a card reader
y Connecting the camera to a computer using the supplied USB cable
Using the Card Reader

Eject the memory card from the camera
and insert it in a card reader that is
connected to a computer.

Open [My Computer] or [Windows
Explorer] and double-click the removable
drive icon that represents the memory
card.

Copy images from the card into a directory of your choice on the
computer’s hard disk.

Connecting the Camera to a Computer with the USB Cable

Install the USB software driver included
with the bundled CD-ROM.

Connect the supplied USB cable to the
computer’s USB port and turn on the
camera.
y The LCD screen turns off when the
connection to the computer has been
successfully completed.

Open [My Computer] or [Windows Explorer]. A “Removable Disk” appears
in the drive list.

Double-click the “Removable Disk” icon to view its contents.
y Files stored on camera are located in the folder name “DCIM”.

3
1
2
3
1
2
4
50
Appendix
About the Folder & File Name
Your digital camera automatically creates a directory of folders in the internal memory or
memory card that it uses to organize still images, movie clips and other information.
Folder Structure
Folder name begins with a 3-digit number from
100 to 999 and followed by “DICAM”, each folder
holds up to 9999 files. If new files are made, a
new folder named in sequence will be made
automatically.

File Naming
File name begins with “DSCI” and are followed by a 4-digit number that increases in
sequence. File numbering starts from 0001 when a new folder is created.

If the highest folder number is 999 and highest file number exceeds 9999, the camera
will display the warning message “Folder cannot be created”. When it appears, try one of
the following ways:

y Reset the file number and plug in a new memory card.
y The folder number and file number are initialized and renumbered from 100 and
0001 respectively.

y Do not change the folder and file names in the memory card using your
computer. It may be unable to playback the data using the digital camera.

C Ca au ut ti io on n
51
Troubleshooting
Problem Cause Solution
Battery is inserted in the wrong
direction.
Reload battery in the correct
direction.
Batteries are dead. Replace or recharge batteries.
Power does not turn on.
The battery compartment door
is open.
Make sure the battery
compartment door is securely
closed.
The flash is charging. Wait for the flash to charge.
Memory is full. Insert a new memory card.
The camera does not take
pictures.
Memory card is not formatted
correctly.
The card may be defective,
use a new card.
The flash is charging. Wait for the flash to charge. Image is not recorded when
the shutter button is pressed. Memory is full. Insert a new memory card.
The flash does not fire. Flash is set to OFF. Set the flash to any mode
except off.
The camera was moving when
the image was captured.
Hold the camera steady when
shooting picture.
Image is blurry or out of focus.
The subject was beyond the
range within which the camera
can focus.
Turn the Macro mode on it the
subject is within 10 cm or 50
cm.
Do not use Macro mode when
shooting distant subjects.
Image is not displayed on the
LCD monitor.
A memory card with non-DCIF
images (recorded with other
camera) is loaded.
This camera cannot display
non-DCIF images.
Recorded images are not
saved in memory.
The camera was turned off /
powered down before the
image was stored in memory.
If the battery low indicator
appears on the LCD monitor,
replace the battery
immediately.
Cannot transfer images to a
computer after connecting the
USB cable.
USB driver is not installed. Install the USB driver before
you connect the camera to a
computer / turn the camera on.
Card error The memory card format may
not be correct.
Re-format the memory card to
the FAT format using a card
reader in Windows.

52
Specifications
Sensor 10 Mega Pixels CCD, Size : 1/1.8 inch
Lens Focal Length : f = 7.4 ( W ) ~ 22.2 ( T ) mm ,
3X optical zoom, 4X digital zoom
LCD monitor 3.0” LCD monitor
Focus Range Normal: 80cm ~ Infinity ( from the tip of barrier )
Macro: (W) 10 cm ~ 80 cm / (T) 50 cm~ 80 cm ( from the tip of
barrier )
Aperture F/ 2.8 ( W ), 5.1 ( T )
Shutter 8 ~ 1/2000 sec.
File Format Still Image: EXIF 2.2 compatible format ( JPEG compression ),
DCF compatible. Support DPOF, ( PictBridge available )
Video: AVI , Audio: WAV
Resolution Still Image: 3584 x 2688 (10M) / 3648 x 2432 (3:2) / 3584 x 2016
(16:9) / 3328 x 2496 (8M) / 2560 x 1920 (5M) / 2048 x 1536 (3M)
/ 640 x 480 (VGA)
Video: 848×480 / 640×480 / 320×240
Scene Mode

Program / Movie / Voice REC / Q. Mode / Portrait / Landscape /
Sunset / Backlight / Night scene / Sports / Party / Snow / Kids /
Candlelight / Fireworks / Night Portrait / Soft Skin / Soft Flowing
Water / Food / Building / Text
Sensitivity Auto / ISO 50 / ISO 100 / ISO 200 / ISO 400 / ISO 800 / ISO 1600
White Balance Auto / Daylight / Cloudy / Tungsten / Fluorescent (H) / Fluorescent
(L) / Custom
Exposure Control -2EV to +2EV in 1/3 step
Metering Center-weighted / Multi / Spot
Burst Depends on the capacity of the memory. (no limit)
Self-timer 2 sec. / 10 sec. / Double
Flash Auto / Red eye reduction / Always on / Slow sync / Always off
Photo Effect Black & White / Sepia / Negative / Mosaic / Red / Green / Blue
Storage 16 MB internal memory / SD Card
TV system NTSC / PAL
Power Supply Rechargeable Lithium-ion Battery (Li-Ion 820 mAh)
Ambient
temperature
Operating: 0° C to 40° C
Storage: -20 to 60° C
Microphone Built-in
Speaker Built-in
Dimension Camera Body ( W x H x T ) : 96 x 24.7 x 59 mm
53
Weight Camera Body w/o battery : Approx. 140 (g)
*These specifications are subject to change without notice.

54

² ² ² ² ² ² ² ² ² ² ² ² ² ² ²

² ² ²
1/15 ~
1/2000
z ⃝ ² ² ² ² ² ² ² ² ²

z ² ² 8~
1/2000
z ² ² ² ² z ⃝ ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ² ² z ² ⃝ ⃝ ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ² ² z ² ⃝ ⃝ ⃝ ⃝ ² ²

z ² ² 8~
1/2000
z ² ² ² ² ² z z ² ² ²

² z ² 1~
1/2000
z ² ² ² ² ² z ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ² ² z ² ² ⃝ ⃝ ⃝ ² ²

z ² ² 1~
1/2000
² z ² ² ² ² z ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ² z ² ² ² ⃝ ⃝ ⃝ ² ²

z ² ² 1~
1/2000
⃝ z z ² ² ² ⃝ ⃝ ⃝ ² ²

² z ² 1~
1/2000
z ² ² z ² ² ⃝ ⃝ ⃝ ² ²

z ² ² 8~
1/2000
z ² ² ² ² z ⃝ ⃝ ⃝ ² ²

² ² z
2 sec.
fixed
z ² ² ² ² ² z z ² ² ²

z ² ² 1~
1/2000
z ² z ² ² ² ⃝ ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ² ² z ² ² ⃝ ⃝ ⃝ ² ²

² ² z 1~
1/2000
z ² ² ² ² ² z ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ² ² ² z ² ⃝ ⃝ ⃝ ² ²
Scene Mode

² ² z 1~
1/2000
z ² ² ² ² ² z ⃝ ⃝ ² ²

z ² ² 1~
1/2000
z ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ²

z ² ² 8~
1/2000
z ⃝ ² ⃝ ⃝ ² z ⃝ ⃝ ⃝ ⃝

z ² ² 8~
1/2000
z ⃝ ² ⃝ ⃝ ² z ⃝ ⃝ ² ⃝

z ² ² 8~
1/2000
z ⃝ ² ⃝ ⃝ ⃝ z ⃝ ⃝ ⃝ ²
Still Capture

z ² ² 1~
1/2000
z ⃝ ” ⃝ ⃝ ⃝ ⃝ ” ⃝ ² ²
One time AF
Continuous AF
Infinity Fixed
Off
On
Auto
Red eye
Force on
Slow sync
Force off
Off
On
Aperturealue
Shutterspeed
Function Available List
Mode
Function
Shutter & Lens
Focus
Shutter Speed
Button
Macro Flash Stabilizer Up & Down
55

² ² ² ² ² ² ² ² ² ² ² ² ² ² ² ²
² ² ² ² ² ² ² ⃝ ” ⃝ ² ² ² ⃝ ⃝ ⃝

⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ² z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ ² ² Scene Mode

⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² z ² ² ² z ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ ⃝ ⃝

⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ ⃝ ⃝

⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ⃝ ⃝ ⃝ ⃝ ⃝
Still Capture

” ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ⃝ ” ⃝ ⃝ ” ⃝
10M
3:2
16:9
8M
5M
3M
VGA
16:9
640
320
Super Fine
Fine
Normal
Center
Multi
Spot
Mode
Function
Menu
Resolution Movie SizeQuality Metering

56

² ² ² ² ² ² ² ² ² ² ² ² ² ² ² ² ²
⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ² ² ² ² ² ² ² ² z ²
z ² ² ² ² ² ²

Leave a Comment