Fujitsu – ST5010D – User Manual

Category: Multimedia Tablet, Graphic Tablet, and eReader User Guides and Manuals

Download user manual for Fujitsu – ST5010D – User Manual 
Preview: Below is a preview of the manual as extracted from the PDF file


Copyright
Fujitsu Computer Systems Corporation has made every
effort to ensure the accuracy and completeness of this
document. Because ongoing development efforts are
made to continually improve the capabilities of our prod-
ucts, however, the data contained herein represents
Fujitsu design objectives and is provided for comparative
purposes; actual results may vary based on a variety of
factors. This product data does not constitute a warranty.
Specifications are subject to change without knowledge.
Fujitsu and the Fujitsu logo are registered trademarks of
Fujitsu Limited; Stylistic is a registered trademark of
Fujitsu Computer Systems Corporation.
Microsoft and Windows are registered trademarks of
Microsoft Corporation.
PCMCIA and CardBus are registered trademarks of the
Personal Computer Memory Card International Associa-
tion.
Intel, Pentium, and SpeedStep are registered trademarks
of Intel Corporation.
Atheros is a registered trademark of Atheros Communi-
cations, Inc.
PowerQuest and Drive Image are registered trademarks
of PowerQuest Corp.
Kensington and MicroSaver are registered trademarks of
the Kensington Technology Group.
SanDisk and the SanDisk logo are registered trademarks
of SanDisk Corporation.
Memory Stick is a registered trademark of Sony Corpora-
tion and/or its affiliates
Wi-Fi is a trademark of the Wireless Ethernet Compati-
bility Alliance (WECA).
All other products are trademarks or registered trade-
marks of their respective companies.
Copyright 2004-Fujitsu Computer Systems Corporation.
All rights reserved. No part of this publication may be
copied, reproduced, or translated, without the prior
written consent of Fujitsu Computer Systems Corpora-
tion. No part of this publication may be stored or trans-
mitted in any electronic form without the prior consent
of Fujitsu Computer Systems Corporation.
B6FH-0561-03EN-00
Note: For more detailed information about the FCC rules and their applicability to the Stylistic ST5000
Series Tablet PC, refer to Chapter 5 of this document.
Warning
Handling the cord on this product will expose
you to lead, a chemical known to the State of
California to cause birth defects or other
reproductive harm.
Wash hands after handling.
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name: Fujitsu Computer Systems Corporation
Address: 1250 E. Arques Avenue, MS 122
Sunnyvale, CA 954085
Telephone: 408-746-6000
Declares that product: Model Series: Stylistic® ST5000 Tablet PC
Complies with Part 15 of the FCC Rules
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and, (2) This device must accept any interference
received, including interference that may cause undesired operation.
Ocampa2_UG.book Page i Thursday, February 19, 2004 5:23 PMStylistic ST5000 Series Tablet PC – User’s Guide
Ocampa2_UG.book Page ii Thursday, February 19, 2004 5:23 PMTable of Contents
Table of Contents
PREFACE
Preface
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . v
Fujitsu Contact Information . . . . . . . . . . . . . . . . . v
Warranty Information . . . . . . . . . . . . . . . . . . . . . v
1
GETTING STARTED
Getting Started with Your Tablet PC
In-box Items for the Stylistic
ST5000 Series Tablet PC . . . . . . . . . . . . . . . . . 1
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . 2
Stylistic Tablet PC Features. . . . . . . . . . . . . . . . . . 3
Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application Buttons . . . . . . . . . . . . . . . . . . . . . . 10
Navigation Buttons. . . . . . . . . . . . . . . . . . . . . . . 12
Tertiary Functions of Application
and Navigation Buttons. . . . . . . . . . . . . . . . . 13
Security Functions of Application Buttons. . . . . . 14
Setting up the Security Panel . . . . . . . . . . . . . . . 14
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Your Security Panel . . . . . . . . . . . . . . . . . 15
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Uninstalling the Security
Panel Application . . . . . . . . . . . . . . . . . . . . . . . . 15
Connectors and Peripheral Interfaces . . . . . . . . . 17
2
USING YOUR TABLET PC
Using the ST5000 Series Tablet PC
System States. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Powering Up the Tablet PC . . . . . . . . . . . . . . . . 22
Shutting Down the System. . . . . . . . . . . . . . . . . 22
Suspending System Operation . . . . . . . . . . . . . . 22
Resuming System Operation . . . . . . . . . . . . . . . 24
Adjusting the Display Brightness. . . . . . . . . . . . . 24
Using the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Calibrating the Pen . . . . . . . . . . . . . . . . . . . . . . 25
Installing a Pen Tether . . . . . . . . . . . . . . . . . . . . 25
Replacing the Pen Tip . . . . . . . . . . . . . . . . . . . . 25
Charging the Battery . . . . . . . . . . . . . . . . . . . . . 26
Removing and Installing the Battery. . . . . . . . . . 26
Tips for Conserving Battery Power . . . . . . . . . . . 27
Modem Connection . . . . . . . . . . . . . . . . . . . . . 27
Memory Stick/SD Card Slot . . . . . . . . . . . . . . . . 27
PC Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Removing and Installing Memory Modules . . . . 28
3
CARE AND MAINTENANCE
Care and Maintenance
Caring for Your Tablet PC . . . . . . . . . . . . . . . . . 33
Protecting the Display Screen. . . . . . . . . . . . . . . 33
Storing the Tablet PC. . . . . . . . . . . . . . . . . . . . . 34
Avoiding Overheating . . . . . . . . . . . . . . . . . . . . 34
Cleaning the Display Screen. . . . . . . . . . . . . . . . 34
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 34
Restoring Your Pre-Installed Software . . . . . . . . 35
Drive Image Special Edition (DISE) . . . . . . . . . . . 36
4
SPECIFICATIONS
ST5000 Hardware Specifications
Processing Specifications . . . . . . . . . . . . . . . . . . 41
Memory/Storage Specifications . . . . . . . . . . . . . 41
Display Specifications. . . . . . . . . . . . . . . . . . . . . 41
Physical Specifications . . . . . . . . . . . . . . . . . . . . 41
Interface Specifications . . . . . . . . . . . . . . . . . . . 41
Power Specifications . . . . . . . . . . . . . . . . . . . . . 42
Environmental Specifications . . . . . . . . . . . . . . . 42
Agency Approval Specifications . . . . . . . . . . . . . 42
Additional Specifications . . . . . . . . . . . . . . . . . . 42
Ocampa2_UG.book Page i Thursday, February 19, 2004 5:23 PMStylistic ST5000 Series Tablet PC User’s Guide
5
AGENCY NOTICES
Regulatory Information
Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
APPENDIX:
WIRELESS LANUSER’S GUIDE
Before Using the Wireless LAN
For Better Communications . . . . . . . . . . . . . . . . 53
Stopping Transmission . . . . . . . . . . . . . . . . . . . . 54
Starting Transmission . . . . . . . . . . . . . . . . . . . . . 54
Connecting the WLAN
Flow of Operations . . . . . . . . . . . . . . . . . . . . . . 55
Preparation for wireless LAN connection . . . . . . 55
Connection to the network . . . . . . . . . . . . . . . . 57
Other settings
Setting of power-saving function . . . . . . . . . . . . 61
Troubleshooting the WLAN
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 62
Wireless LAN Glossary
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
IP address information
Additional Information. . . . . . . . . . . . . . . . . . . . 66
WLAN Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Index
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Ocampa2_UG.book Page ii Thursday, February 19, 2004 5:23 PMPreface
Ocampa2_UG.book Page iii Thursday, February 19, 2004 5:23 PMStylistic ST5000 Series Tablet PC User’s Guide – Preface
Ocampa2_UG.book Page iv Thursday, February 19, 2004 5:23 PMPreface
Preface
ABOUT THIS GUIDE
The Stylistic

ST5000 Series Tablet PC is a high-
performance, pen-based computer that has been
designed to support Microsoft

Windows

XP Tablet PC
Edition.
This manual explains how to operate your Fujitsu
Stylistic ST5000 Series Tablet PC’s hardware and built-in
system software.
The Stylistic ST5000 Series Tablet PC is a completely self-
contained unit with an active-matrix (TFT) color LCD
display and an active digitizer. It has a powerful interface
that enables it to support a variety of optional features.
Conventions Used in the Guide
Keyboard keys appear in brackets.
Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].
Pages with additional information about a specific topic
are cross-referenced within the text.
Example: (See page xx.)
On screen buttons or menu items appear in bold
Example: Click OK to restart your Tablet PC.
DOS commands you enter appear in Courier type.
Example: Shut down the computer?
FUJITSU CONTACT INFORMATION
Service and Support
Y ou can contact Fujitsu Service and Support in the
following ways:

T oll free: 1-800-8Fujitsu (1-800-838-5487)

Fax: 408-764-2724

E-mail: 8fujitsu@us.fujitsu.com

Web site: http://us.fujitsu.com/computers
Before you place the call, you should have the
following information ready so the customer support
representative can provide you with the fastest possible
solution:

Product name

Product configuration number

Product serial number

Purchase date

Conditions under which the problem occurred

Any error messages that have occurred

Hardware configuration

Type of device connected, if any
Fujitsu Online
Y ou can go directly to the online Fujitsu product catalog
for your Tablet PC by going to the Fujitsu Web site at:
http://us.fujitsu.com/computers.
WARRANTY INFORMATION
Y our Stylistic ST5000 Series Tablet PC is backed by an
International Limited Warranty. Check the service kit
that came with your system for warranty terms and
conditions.
The information icon highlights
information that will enhance your
understanding of the subject material.
The caution icon highlights information
that is important to the safe operation of
your computer, or to the integrity of your
files. Please read all caution information
carefully.
The warning icon highlights information
that can be hazardous to either you, your
computer, or your files. Please read all
warning information carefully.
You must have an active internet connec-
tion to use the online URL links.
Ocampa2_UG.book Page v Thursday, February 19, 2004 5:23 PMStylistic ST5000 Series Tablet PC User’s Guide – Preface
Ocampa2_UG.book Page vi Thursday, February 19, 2004 5:23 PM1
Getting Started
with Your Tablet PC
Ocampa2_UG.book Page vii Thursday, February 19, 2004 5:23 PMStylistic ST5000 Series Tablet PC User’s Guide – Section One
Ocampa2_UG.book Page viii Thursday, February 19, 2004 5:23 PM1
Getting Started
Getting Started with Your Stylistic Tablet PC
Figure 1-1. Stylistic ST5000 Series Tablet PC
The Stylistic

ST5000 Series Tablet PC is a high-
performance, pen-based computer that has been
designed to support Microsoft

Windows

XP T ablet PC
Edition. This chapter provides an overview of the Stylistic
ST5000 Series Tablet PC and its features.
IN-BOX ITEMS FOR THE STYLISTIC
ST5000 SERIES TABLET PC
V erify that the following items are included in the box
with your Tablet PC:
 Stylistic ST5000 Series active pen
 Pen tips (quantity: 5)
Pen tip removal tool
Pen tether
 Main battery
Power cord
AC adapter
 Screen protectors (quantity: 2)
 Getting Started Guide
 Quick Tips Guide
The Stylistic ST5000
Series Tablet PC is available
with either a 10.4” reflective display
or a 12.1” transmissive display. For purposes
of illustration, the 12.1” model is used throughout.
Please refer to the Specifications chapter for additional details.
Ocampa2_UG.book Page 1 Thursday, February 19, 2004 5:23 PM2
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
OPTIONAL ACCESSORIES
The following optional accessories can be used with the Stylistic ST5000 Series Tablet PC. Refer to the
instructions provided with these accessories for details on their use.
* For the latest list of accessories available for your Stylistic ST5000 Series Tablet PC, be sure to frequently check the Fujitsu
Web site at: http://us.fujitsu.com/computers.
Table 1-1. Stylistic ST5000 Series Optional Accessories
Peripheral/Accessory Fujitsu Part Number
Docking Options
Tablet PC Tablet Dock, with CD-ROM drive FPCPR44AP
Tablet PC Tablet Dock, with Combo DVD/CD-RW drive FPCPR43AP
Universal Mount Adapter FPCPR46
Carrying Cases
Tablet PC Executive Leather Portfolio Case FPCCC45
Tablet PC Ballistic Nylon Attaché Case FPCCC46
Easel Case FPCCC49
Hand Strap FPCETC13
Media Options
External USB Floppy Disk Drive FPCFDD12
External DVD/CD-ROM Combo Drive FPCDVR26
USB CD-ROM Drive FPCCD33AP
Memory
256 MB SO DIMM, DDR333 FPCEM99AP
512 MB SO DIMM, DDR333 FPCEM100AP
1 GB SO DIMM, DDR333 FPCEM101AP
128 MB Compact Flash Card FPCEMC02
256 MB Compact Flash Card FPCEMC03
128 MB Secure Digital Memory Card FPCEMC01
Power Options
AC Adapter with US Cord FPCAC37AP
Main Battery FPCBP77AP
High-Capacity Battery FPCBP78AP
Auto/Airline Adapter FPCAA02
Battery Charger FPCBC06
Input Devices
Wireless Keyboard FPCKB41A1P
Wireless Keyboard with Pointing Device FPCKB51A1P
Logitech Wireless Keyboard and Mouse FPCKB04
USB Optical Mouse FPCMO08AP
Stylistic ST5000 Tablet PC Pen (2-pack) FPCPN07AP
Additional Accessories
Screen Protectors (6-pack) FPCSP04AP
HEC Screen Protectors (2-pack) FPCSP07
4 in 1 PC Card Adapter (SD/MMC/Memory Stick/SmartMedia) FPCPCC01
Compact Flash Card Adapter FPCCFA01
Netgear 802.11g Gateway/Router FPCRT01
Notebook Guardian Lock FPCLCK02
Ocampa2_UG.book Page 2 Thursday, February 19, 2004 5:23 PM3
Getting Started
STYLISTIC TABLET PC FEATURES
Features and controls that you use to operate the Stylistic ST5000 Series Tablet PC are outlined below and illustrated in
Figures 1-1 through 1-5. Details on using these features and controls are provided later in this manual.
Figure 1-2. Stylistic ST5000 Series Tablet PC Features (Front View)
Front Features: 1
 System status LEDs: Indicate the operational status of
the Tablet PC and hard disk drive, the charge level of
the battery, and the security panel.
 Power On/Suspend/Resume button: Allows you to
turn on, off, suspend, resume, hibernate or wake the
Tablet PC in order to optimize battery life.
 Infrared keyboard/mouse ports: The infrared ports
are used for communicating with a proprietary
infrared keyboard or mouse.

 Application buttons: Allow you to quickly launch
pre-defined applications and utilities by pressing a
button.
 Navigation buttons: The navigation buttons allow
you to move: Page Up/Page Down, Tab Right/Tab
Left, Cursor Up/Cursor Down, and Cursor Right/
Cursor Left.
 Speaker: Allows you to listen to mono audio files.
 Built-in Microphone: The built-in microphone allows
you to input mono audio.

These peripherals and accessories are sold separately.
Power On/Suspend/
System
Status
Resume Button
Built-in
Speaker
Navigation
Buttons
LEDs
User-Programmable
Application Buttons
Microphone
Infrared Keyboard/
Mouse Port
Infrared Keyboard/
Mouse Port
Ocampa2_UG.book Page 3 Thursday, February 19, 2004 5:23 PM4
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
Figure 1-3. Stylistic ST5000 Series Tablet PC Features (Back View)
* The system is configured with one of two modules: a standard modem/LAN module or an optional wireless LAN/LAN/
modem combo module.
Back Features: 1
 System interface connector: Allows you to connect
the optional Stylistic Tablet Dock.

 Removable battery: Can be removed and replaced
with a charged battery.

 Battery release latch: Used to release the removable
battery.
 Tablet Dock latch point: Allows you to attach the
system to an optional Tablet Dock.

 Memory module cover: Removable cover over the
memory modules.
 Thermal Suede: Several areas of the system back are
covered with “thermal suede” . This material should
not be removed. It is designed to minimize the heat
that the user feels when the system has been
operating for an extended period of time.
 Wireless LAN module cover: Provides protection for
the optional wireless LAN radio.
 Wireless LAN On/Off switch: For systems with the
optional wireless LAN radio, this switch toggles the
radio on or off, allowing the user to maximize battery
life when wireless LAN functionality is not needed.

These peripherals and accessories are sold separately.
Battery
Memory
Battery
System
Release
Latch
Module
Cover
Interface
Connector
Tablet Dock
Latch Points
Thermal Suede
Wireless LAN*
On/Off Switch
Ocampa2_UG.book Page 4 Thursday, February 19, 2004 5:23 PM5
Getting Started

Figure 1-4. Stylistic ST5000 Series Tablet PC Features (Top View)
Top Features: 1
 Pen: The main input device that you use to execute
programs and enter data. A pen holder is built into
the Tablet PC to store the pen when not in use.
 Pen Tether Point: The pen tether point is used to
attach a pen tether to help prevent loss of the pen.
 PC Card slot: Allows you to install a Type I or Type II
PCMCIA Card

in the system.
 PC Card Eject Button: The PC Card eject button is
used to remove a PC Card from the PC Card slot.
 Air flow vents: Provides secondary cooling for
processor. (Do not obstruct the vents.)
 SD Card/Memory Stick Slot: The Secure Digital (SD)
card/Memory Stick slot allows you to install a flash
memory card

for data storage. Flash memory cards
allow you to transfer data to and from a variety of
different digital devices.
 IrDA/FIR port: Provides an infrared interface for
communication with devices compliant with IrDA
Standard Revision 1.1.
 Smart Card Slot: The dedicated Smart Card slot
allows you to install a Smart Card

on which you can
store such data as medical information or electronic
“cash” .

These peripherals and accessories are sold separately.
Pen Holder
Smart Card Slot
PC Card
Eject Button
Air flow vents
PC Card Slot
SD Card/Memory Stick Slot
IrDA/FIR Port
Pen Tether Point
Ocampa2_UG.book Page 5 Thursday, February 19, 2004 5:23 PM6
Stylistic ST5000 Series Tablet PC User’s Guide – Section One

Figure 1-5. Stylistic ST5000 Series Tablet PC Features (Left Side View)
* The system is configured with one of two modules: a standard modem/LAN module or an optional wireless LAN/LAN/
modem combo module.
Left-Side Features: 1
 USB 2.0 ports: Allow you to connect Universal Serial
Bus-compliant devices (compliant with USB
Standard Revision 2.0) to the Tablet PC. Additional
USB ports are located on the optional Tablet Dock

.
 Headphone Jack: Allows you to connect a set of
stereo headphones

.
 Microphone Jack: Allows you to connect an external
microphone

.
 IEEE 1394 Jack: Allows you to connect IEEE 1394
(Firewire) peripherals such as digital video cameras

or external hard drives

to your Tablet PC.
 External Monitor Connector: The External Monitor
connector allows you to connect an external VGA,
XGA, or SVGA CRT monitor.
 Modem jack: Allows you to connect a standard RJ-11
connector to the Tablet PC’s internal 56 Kbps
modem. Note that the internal 56 Kbps LAN/modem
module installed in the Stylistic ST5000 Series Tablet
PC has actual maximum transfer rates of 53 Kbps
(receive), 33.6 Kbps (send), and 14.4 Kbps (fax).
Download rates are limited to 53 Kbps in the United
States due to FCC restrictions.
 LAN jack: Allows you to connect a standard RJ-45
connector to the Tablet PC’s internal local area
network (LAN).
 Kensington™ lock slot: Allows you to attach a
Kensington MicroSaver
TM
-compatible security
cable.

 DC input connector: Allows you to connect the AC
adapter or auto adapter.


These peripherals and accessories are sold separately.
LAN Jack*
Modem Jack*
Kensington™ Lock Slot
DC Input Jack
External Monitor Connector (behind cover)
Latch Point
USB 2.0 Ports
Headphone Jack
Microphone Jack
IEEE 1394 Jack
Ocampa2_UG.book Page 6 Thursday, February 19, 2004 5:23 PM7
Getting Started
Figure 1-6. Stylistic ST5000 Series Tablet PC Features (Right Side View)
Right-Side Features: 1
 Pen: The main pointing device that you use to execute
programs and enter data. A pen holder is built into
the Tablet PC to store the pen when not in use.
 Infrared keyboard/mouse port: The infrared port
wraps around the front and bottom of the display,
and is used for communicating with an optional
proprietary infrared keyboard or mouse

.
 Wireless LAN location: The optional wireless LAN
device is located inside of the system housing.

These peripherals and accessories are sold separately.
Pen / Pen Holder
Infrared Keyboard/Mouse Port
Latch Point Optional Wireless LAN location
Ocampa2_UG.book Page 7 Thursday, February 19, 2004 5:23 PM8
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
STATUS DISPLAY
Icons appear under each of the system status LEDs in the
status display indicating the status of system functions
such as system power and battery charge level. The loca-
tion of icons in the Status display is shown in Figure 1-7.
Table 1-2. explains how the LEDs associated with the
individual icons are displayed, and describes what the
variations of that display indicate. (If an icon is not
displayed, it indicates that the related system function is
off or inactive.
Figure 1-7. Status Display Icons
Power
Charge/DC In
Battery
HDD Access
Security
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the
rate of one second on, five seconds off.
Icon Mode/State LED State Remarks
Power  On State
 Idle Mode
Green, continuous The system is powered on and ready for use.
 Suspend-to-RAM Green, blinking The system has suspended and saved active
settings to RAM.
 Off State
Hibernate
(Save-to-Disk)
Off The system has suspended and saved settings
and data to the hard disk drive.
Charge/DC
In
 On State
 Idle Mode
 Suspend-to-RAM
Hibernate
(Save-to-Disk)
 Off State
Amber AC adapter and battery are available and system
is charging.
Green  AC adapter and battery are available and
system is not charging (battery fully
charged).
 AC adapter is available but battery is not
present.
Amber, blinking AC adapter and battery are available and waiting
to charge (battery is out of thermal range).
Off AC adapter is not available.
Ocampa2_UG.book Page 8 Thursday, February 19, 2004 5:23 PM9
Getting Started
Table 1-2. System Status Indicators
Battery  On State
 Idle Mode
Green, continuous Battery charge is between 50%-100%
Amber, continuous Battery charge is between 13%-49%
Red, continuous Battery charge is between 0%-12%
Red, blinking There is a battery error.
 Suspend-to-RAM,
without AC adapter
 Suspend-to-RAM
with AC adapter
Green, blinking slow Battery charge is between 50%-100%.
Amber, blinking slow Battery charge is between 13%-49%.
Red, blinking slow Battery charge is between 0%-12%.
Hibernate
(Save-to-Disk),
with AC adapter
 Off State
Off Battery is not installed, or system is off or in
Hibernate mode.
Hibernate
(Save-to-Disk),
without AC adapter
If battery is inserted during power off, LED blinks
amber for 4 seconds to detect battery. Battery
status is displayed for 5 seconds after that.
HDD
Access
 On State (or
flashing)
 Idle Mode
Green Displayed when hard disk drive is accessed.
 Suspend-to-RAM
Hibernate
(Save-to-Disk)
 Off State
Off Hard disk drive is not being accessed.
Security  On State Green, continuous
(until password is
entered)
The Security Indicator lights (if a password was
set) when the system resumes from Off or
Standby modes. You must enter the password
that was set in the Security Panel before your
system will resume operation.
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the
rate of one second on, five seconds off.
Icon Mode/State LED State Remarks
Ocampa2_UG.book Page 9 Thursday, February 19, 2004 5:23 PM10
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
APPLICATION BUTTONS
The six application buttons are located on the upper
right-hand side of a vertically-oriented system. (See
figure 1-2 on page 3 for location). Five of the buttons have
secondary functions. The secondary functions are acti-
vated by pressing the Function (Fn) button while
pressing the application button.
The buttons also have separate tertiary functions that
can be used while the system is booting up. For more
information about the tertiary functions, refer to
Table 1-5 on page 13.
Ctl-Alt-Del is the only Application button
that can be used while the system is
logging on or when the system is locked
(i.e., when you have the Logon or
Computer Locked window showing on
your desktop).
Button Icon
and Name
(Primary)
Tablet Icon
(Fn +
Button)
(Secondary)
Description
Ctl-Alt-Del
Button
Security
Button
Pressing the Ctl-Alt-Del button for approximately one second allows you to log on
after boot, after locking the workstation, or after resuming from power
management.
Security Button: All five buttons are used when implementing security functions.
Four of the buttons are used to enter the password, and the fifth is used as an
Enter button. See “Security Functions of Application Buttons” on page 14.
EMail
Button
Internet
Button
When you press the EMail button, you automatically launch Microsoft Outlook
where you can read, create, and send emails.
When you press the Fn + EMail buttons at the same time, you automatically
launch the Web browser. The default page to which you go is the Fujitsu home
page. If you would like to change your home page, go to the Control Panel->
Internet Options. Select the General tab and enter the starting address you would
like to use.
Orientation
Button
Display
Mode
Button
When you press the Orientation button, the system screen orientation changes
from portrait (vertical) to landscape (horizontal) or from landscape to portrait.
When you would like to use the Tablet PC as an eBook, for example, you would
use the portrait orientation, when accessing spreadsheets, you would more
typically use a landscape orientation.
When you press the Fn + Orientation buttons at the same time*, the Graphics
Options Output menu is launched. From that menu you can choose the display
mode you would like to use.
Escape
Button
Application
A Button
The Escape application button acts the same way as an Escape key on a keyboard.
When you press the Fn + Esc buttons at the same time*, they act to invoke a pre-
determined application or generate a combination keystroke, as assigned in the
Tablet Button Settings utility. (You can change the settings in Control Panel ->
Tablet Button Settings).
By default, pressing the Fn + Esc combination acts the same as if you had pressed
Ctl + Esc on a keyboard: the Start menu is launched.
Ocampa2_UG.book Page 10 Thursday, February 19, 2004 5:23 PM11
Getting Started
Table 1-3. Application Buttons – Primary and Secondary Functions
* The Fn button has a handy “sticky” feature that allows you to press two buttons in immediate succession, rather
than at exactly the same time. After pressing the Fn button, you have a short time (2 to 3 seconds) to press the
second button.
Enter
Button
Application
B Button
The Enter application button acts the same way as an Enter key on a keyboard.
Pressing the Fn + Ent buttons at the same time*, acts to invoke a pre-determined
application or keystroke combination, as assigned in the Tablet Button Settings
utility. (You can change the settings in Control Panel -> Tablet Button Settings).
By default, pressing the Fn + Ent combination acts the same as if you had pressed
Alt on a keyboard: it selects a main menu in the typical Windows application.
Function
Button
Fujitsu
Menu
Utility
The Function button works in conjunction with the other application buttons to
provide additional functionality for the buttons. Refer to specific details above.*
Pressing the Fn button twice in succession (within the “sticky” time*), causes the
Fujitsu menu to appear on your screen, allowing you to modify certain system
settings.
Button Icon
and Name
(Primary)
Tablet Icon
(Fn +
Button)
(Secondary)
Description
Ocampa2_UG.book Page 11 Thursday, February 19, 2004 5:23 PM12
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
NAVIGATION BUTTONS
The two navigation buttons are located on the lower
right-hand side of a vertically-oriented system. (See
figure 1-2 on page 3 for location). Each of the buttons can
be toggled by pressing either end of the button.
The buttons have dual functions. The secondary func-
tions are activated by pressing the Function (Fn) button
while pressing the application button*.
The buttons also have separate tertiary functions that
can be used while the system is booting up. For more
information about the tertiary functions, refer to
Table 1-5 on page 13.
* The Fn button has a handy “sticky” feature that allows you to press two buttons in immediate succession, rather
than at exactly the same time. After pressing the Fn button, you have a short time (2 to 3 seconds) to press the
second button.
Table 1-4. Navigation Buttons
Ctl-Alt-Del is the only Application button
that can be used while the system is
logging on or when the system is locked
(i.e., when you have the Logon or
Computer Locked window showing on
your desktop).
Buttons/icons Purpose (when pressed alone)
(“Primary” function)
Purpose (when pressed with Fn button)
(“Secondary” function)
This button consists of Page Up and Page
Down segments. When the Page Up
portion is pressed, you will scroll up one
page.
When the Page Down portion is pressed,
you will scroll down one page.
When pressed with the Function (Fn) button*, the
Up portion of this button allows you to tab right.
When pressed with the Function (Fn) button*, the
Down portion of this button allows you to tab left.
This button consists of Up and Down
segments. When the Up portion is
pressed, the cursor will move up.
When the Down portion is pressed, the
cursor will move down.
When pressed with the Function (Fn) button*, the
Up portion of this button will move the cursor to the
right.
When pressed with the Function (Fn) button*, the
Down portion of this button will move the cursor to
the left.
Ocampa2_UG.book Page 12 Thursday, February 19, 2004 5:23 PM13
Getting Started
TERTIARY FUNCTIONS OF APPLICATION AND NAVIGATION BUTTONS
While you are booting up your system, the Application
Buttons and Navigation buttons can be used for entering
and navigating through the Basic Input-Output System
(BIOS), and for invoking the Advanced Options Menu,
where you can enter different modes (such as Safe
Mode).
The BIOS is a program and a set of parameters that are
stored in ROM, which tests and operates your Tablet PC
from when you turn it on until it loads your installed
operating system from disk. Information from the BIOS
is transferred to the operating system to provide it with
information on the configuration and status of the hard-
ware.
The system is booting up while the Fujitsu logo is
displayed immediately after turning on the system. The
table below indicates how the buttons act while the
system is booting up and while you are in the BIOS.
Table 1-5. Tertiary Functions of Application and Navigation Buttons
Buttons/icons Purpose (when pressed while the system is booting up)
Ctl-Alt-Del
Button
Pressing the Ctl-Alt-Del button while the system is booting up takes you into BIOS setup. This is the
same as if you had tapped [F2] on a keyboard.
EMail Button
Pressing the EMail button while the system is booting up opens the Boot Options menu. This is the
same as if you had tapped [F12] on a keyboard.
Orientation
Button
Pressing the Orientation button while the BIOS setup screen is open causes the selected item (if
applicable) to change to the next item. Pressing this is the same as tapping the spacebar on a
keyboard.
Escape Button
Pressing the Esc button while the BIOS is open acts to escape from the BIOS. This is the same as if
you had tapped [Esc] on a keyboard.
Enter Button
Pressing the Ent button while the BIOS is open acts the same as the [Ent] button on a keyboard.
Function Button
Pressing the Fn button while the system is displaying the operating system boot menu, opens the
Advanced Operating System Options menu. This menu allows you to enter different operating
system modes (such as Safe Mode). Pressing this button is the same as if you had tapped [F8] on a
keyboard.
Pressing the top half of the upper navigation button while the BIOS setup screen is open causes the
cursor in the BIOS setup screen to move up. This is the same as if you had tapped Arrow Up on a
keyboard. This feature is also functional in the operating system boot menu.
Pressing the bottom half of the upper navigation button while the BIOS setup screen is open causes
the cursor in the BIOS setup screen to move down. This is the same as if you had tapped Arrow Down
on a keyboard. This feature is also functional in the operating system boot menu.
Pressing the top half of the lower navigation button while the BIOS setup screen is open causes the
cursor in the BIOS setup screen to move right. This is the same as if you had tapped Arrow Right on a
keyboard.
Pressing the bottom half of the lower navigation button while the BIOS setup screen is open causes
the cursor in the BIOS setup screen to move left. This is the same as if you had tapped Arrow Left on
a keyboard.
Ocampa2_UG.book Page 13 Thursday, February 19, 2004 5:23 PM14
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
SECURITY FUNCTIONS OF APPLICATION BUTTONS
Five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and
the fifth is used as an Enter button. Instructions for using the security feature follow the table.
Table 1-6. Security Functions of Application Buttons
SETTING UP THE SECURITY PANEL
When you receive your Tablet PC, the security panel
application is pre-installed without any passwords. The
following sections provide detailed information on your
security panel, how to set, change or remove passwords.
Numbered Buttons
Use these buttons to enter your password.(Figure 1-6)
Enter Button
After entering the button strokes, push this button to
enter the password into the Tablet PC. (Figure 1-6)
PASSWORDS
The user and supervisor password may be set on this
Tablet PC. A supervisor password is typically the same
for all T ablet PC’s and notebooks in a work group, office,
or company to allow for system management. Individual
computers in a group environment should not use a
common password. A password consists of one to five
button strokes plus the enter button. A valid stroke
consists of pushing one or up to four buttons simulta-
neously.
The following are valid button strokes:

Pushing [4] by itself

Pushing [2] and [3] at the same time

Pushing [1], [2], and [4] at the same time

Pushing [1], [2], [3], and [4] at the same time
The following are valid passwords. The numbers within
braces ({ }) are button strokes using more than one
button.

{[2]+[3]}, [1], [Enter]

[4], [enter]

{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]
Setting Passwords
When shipped from the factory, no passwords are set.
Y ou have a choice of having no password or setting a
supervisor and user password. Y ou must set the super-
visor password before the user password.
Button Icons Security Icons Security Purpose
Ctl-Alt-Del Button
Security Enter Button
EMail Button
1 Security Button 1
Orientation Button
2 Security Button 2
Escape Button
3 Security Button 3
Enter Button
4 Security Button 4

The purpose of supervisor password is to
be able to bypass the user password in
case the user password is forgotten. The
supervisor password alone will not lock
the system.

You must set the supervisor and user
passwords for the security panel to work.
Ocampa2_UG.book Page 14 Thursday, February 19, 2004 5:23 PM15
Getting Started
Setting Supervisor Password
Y ou must have set a supervisor password before setting
any user passwords. The supervisor password can bypass
the user password.
1. Go to the Start menu.
2. Click on Run.
3. Type in:
C:Program FilesFujitsuSecurity
Panel ApplicationSupervisor
FJSECS.EXE, then press [Enter]
4. Follow the on-screen instructions to set the
Supervisor password.
Setting User Password
1 Go to the Start menu.
2. Click on All Programs.
3. Click on Security Panel Application -> Security
Panel Application.
4. Follow the on-screen instructions to set the
user password.
USING YOUR SECURITY PANEL
The security lock feature is in effect both when the system
resumes from Off, Standby, or Hibernation state. Y ou
always need to push the Security Panel buttons to input the
user password. Y our system will not begin the boot
sequence until you enter your supervisor/user password.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
For example, if the password is 22222, first press
Button 2 five times and press the Enter button. The
Tablet PC will boot to normal operation.
From Standby/Hibernation State
1. Press your Suspend/Resume button.
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
The Tablet PC should resume normal operation.
Incorrect Password Entry
If an invalid supervisor or user password is entered three
times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute
(while system beeps), the beeping will stop and the T ablet
PC will resume normal operation. If no password is
entered or an invalid password is entered while the
system beeps, the system will return to its previous locked
state (standby or off) and the Security Indicator will go
off. T o reactivate the Tablet PC after a password failure,
you must press the Suspend/Resume button, then enter a
correct password.
PRECAUTIONS
Low Battery Operations
If your Tablet PC has a low battery, pushing the suspend/
resume button does not unlock the Tablet PC. T o resume
normal operation, first attach a power supply to the
system. Then you may unlock the Tablet PC.
UNINSTALLING THE SECURITY
PANEL APPLICATION
Y ou have two options when uninstalling the security
panel application:

Remove passwords and uninstall the security panel
application software. This will disable all security
features.

Uninstall the security panel application with password
still active. This will not allow any changes to the
password.
Uninstalling the Security Panel
Application Software
Remove passwords when User wants no password protec-
tion whatsoever and doesn’t want to give anybody the
utility to set a password on their computer. In this case, if
passwords (supervisor, user, or both) are set, the pass-
words must first be cleared BEFORE removing the appli-
cation. T o clear passwords, follow same procedure in
SETTING PASSWORD CODES except this time, select
REMOVE, enter current password then click Next. When
asked to confirm select Yes.
You may change or remove the supervisor
or user password by repeating the steps
defined above.
Remember the user password you specified
on the Security Panel Application. If you
forget the password you will not be able to
use your computer. The supervisor pass-
word can override the user password.
Ocampa2_UG.book Page 15 Thursday, February 19, 2004 5:23 PM16
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
Removing Security Panel Application with
Passwords Still Active
Using this feature will not allow any changes to
the password.
User:
1. Go to Start -> Control Panel.
2. Open Add or Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application in the list, and
click Change/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Supervisor:
1. Go to Start -> Control Panel.
2. Open Add or Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application for
Supervisor in the list, and click Change/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Reinstalling the Security Panel Application
T o reinstall supervisor or user security application, you
will need your Drivers and Applications CD. The
UtilitiesSecurity Panel Application folder contains two
separate folders: Supervisor and User. The setup files for
supervisor and user security applications are contained
in those folders.
1. Go to the UtilitiesSecurity Panel Application
Supervisor folder on the CD and double-click the
setup.exe file. The Installing Security Panel Applica-
tion window will appear. Follow the instructions on
the screen.
2. Go to the UtilitiesSecurity Panel ApplicationUser
folder on the CD and double-click the setup.exe file.
The Installing Security Panel Application window
will appear. Follow the instructions on the screen.
Supervisor and user passwords can be set via Windows
software using the FJSECS.exe and FJSECU.exe files,
respectively. FJSECU.exe for the user password cannot
run without first setting a supervisor password. Y ou
need to run FJSECS.exe first to set the supervisor pass-
word. Follow instructions under Setting Passwords on
page 14.
If you forget both passwords, please contact Fujitsu
Computer Systems Corporation Service and Support at
1-800-8Fujitsu (1-800-838-5487). Fujitsu Computer
Systems Corporation charges a service fee for unlocking
a password-restricted Tablet PC. When calling please
have a valid credit card and provide proof of ownership.
Y ou will then be given instructions on where to ship
your Tablet PC.
Removing the applications does not remove
the password. It simply removes the utility
to change/add/remove passwords. To
change your password you must reinstall
the application.
Ocampa2_UG.book Page 16 Thursday, February 19, 2004 5:23 PM17
Getting Started
CONNECTORS AND PERIPHERAL INTERFACES
Connectors and peripheral interfaces on the Stylistic
ST5000 Series T ablet PC allow the connection of a variety
of devices. Specific locations are illustrated in Figures 1-2
through 1-5.
Table 1-7 provides a description of each peripheral
connector on the Stylistic ST5000 Series Tablet PC. Each
of the illustrated icons is either molded into or printed on
the Tablet PC chassis.
Connector/
Peripheral
Tablet PC
Icon
Purpose
DC input
connector
Connect an external power source such as the AC adapter or auto/
airline adapter.
USB Port Connect Universal Serial Bus 2.0 compliant devices to the Tablet PC.
PCMCIA
Card slot

Install a Type I or Type II PC Card.
SD Card/
Memory Stick
slot
Install a Secure Digital (SD) Card or a Memory Stick.
Microphone
jack
Connect an external microphone. The internal microphone is disabled
when you plug in an external microphone.
Headphone
jack
Connect stereo headphones or powered external speakers. The internal
speaker is disabled when you plug in external headphones or powered
speakers.
IrDA/FIR port An infrared transceiver built into the Tablet PC allows you to
communicate with other devices that are compliant with the IrDA
Standard Rev. 1.1. Effective range for infrared communication is about
3 feet, and within 15 degrees off center. A clear line-of-sight path must
exist between the IrDA port on the Tablet PC and the IrDA transceiver
on the other device.
Modem Connect a telephone line to the optional internal modem using a
standard RJ-11 telephone plug.
Tablet Dock
port
Connect the Stylistic ST5000 Series Tablet Dock or other approved
docking device. Refer to documentation accompanying the docking
device for more information.
Ocampa2_UG.book Page 17 Thursday, February 19, 2004 5:23 PM18
Stylistic ST5000 Series Tablet PC User’s Guide – Section One
Table 1-7. Peripheral Connectors/Interfaces
Infrared
keyboard/
mouse port
An infrared receiver built into the Tablet PC allows you to communicate
with a Fujitsu wireless infrared keyboard or mouse. The keyboard
infrared port works optimally when it is placed between 10 to 30 cm
(approximately 4 in. to 12 in.) from the keyboard infrared port (which is
located on the bottom edge of the Tablet PC). Ensure there is a clear
line-of-sight path between the infrared receiver on the Tablet PC and
the infrared transmitter on the keyboard or mouse. Note that an
infrared keyboard or mouse works best when the system is in landscape
orientation.
Kensington
TM

Lock slot
The Kensington

Microsaver
TM
security slot allows you to secure the
Tablet PC using Kensington-compatible locking devices.
IEEE 1394 jack The IEEE 1394 jack allows you to connect IEEE 1394 (Firewire) devices
such as digital video cameras and external hard rives to your Tablet PC.
Suspend/
Resume button
The Suspend/Resume/Power On button allows you to suspend Tablet
PC activity without powering off, resume your Tablet PC from suspend
mode, and power on the system when it has been shut down from
Windows.
Page Up/
Page Down
The Page Up/Page Down button allows you to navigate quickly from
page to page without scrolling.
Local Area
Network (LAN)
The LAN (RJ-45) jack is used to connect the internal10/100/1000* Base-
T/Tx Ethernet to a Local Area Network (LAN) in your office or home, or
broadband devices such as a cable modem, DSL, or satellite internet.
*1000 Mbps, commonly referred to as Gigabit Ethernet.
Battery Release
Latch
The battery release latch allows you to remove the battery from your
system for storage or replacement.
Wireless LAN
On-Off Switch
The wireless LAN switch allows you to turn power to the optional
wireless LAN device on and off.
Connector/
Peripheral
Tablet PC
Icon
Purpose
Ocampa2_UG.book Page 18 Thursday, February 19, 2004 5:23 PM19
2
Using Your
Stylistic ST5000
Series Tablet PC
Ocampa2_UG.book Page 19 Thursday, February 19, 2004 5:23 PM20
Stylistic ST5000 Series Tablet PC User’s Guide – Section Two
Ocampa2_UG.book Page 20 Thursday, February 19, 2004 5:23 PM21
Using Your Stylistic ST5000
Using the Stylistic ST5000 Series Tablet PC
This chapter covers the fundamental concepts, basic
system operation and use, and system functions of the
Stylistic ST5000 Series Tablet PC. Y ou should familiarize
yourself with this information before you attempt to
operate the system.
SYSTEM STATES
Before you begin using the Stylistic ST5000 Series Tablet
PC, review the different system states (or modes) that the
system can use. Being familiar with these states will help
you determine whether it is appropriate to turn on,
resume, suspend, hibernate or shut down the system
when you begin or end a session. System behavior for
each system state is described briefly in the following,
with each system state listed in decreasing order of power
usage:
 On state: The system is running and the display
screen is on.
 Idle state: Some system functions are regulated or
turned off to conserve power. The display screen may
be turned off. The system returns to the On state
when pen activity or other input is detected.
 Suspend-to-RAM mode (S3): System operation is
suspended. Most system functions are turned off to
conserve power. Power to memory is on, maintaining
data in programs that were running before system
operation was suspended. The system does not
respond to the pen or other input when in Suspend-
to-RAM mode. Refer to the “Resuming System
Operation” section later in this chapter for
information on returning the system to the On state.
 Hibernate mode (Save-to-Disk) (S4): System
operation is suspended. All system functions are
turned off to conserve power. Active data in programs
that were running before suspending system
operation is stored on the hard disk drive. The system
does not respond to the pen or other input. Refer to
the “Resuming System Operation” section later in this
chapter for information on returning the system to
the On state.
 Off state: All system functions are turned off to
conserve power. The system does not respond to the
pen or other input. The system boots at the next
system power-on.
Y our system may be configured to enter some of these
states automatically after a period of inactivity to
conserve battery power.
When you use the Stylistic ST5000 Series Tablet PC, you
can change the current system state in a number of ways,
depending on the system’s current state. T o determine the
current system state, observe the Power icon in the Status
display. Table 2-1 on page 22 gives the different system
states represented by the Power icon and describes how
you can change the system state from the current state.
Prior to using your system, be sure to fully
charge the battery if you plan to run on
battery power. Failure to do so may result
in erratic performance.
The system consumes the same amount of
power whether it is in Hibernate (Save-to-
Disk) mode or the Off state.
Ocampa2_UG.book Page 21 Thursday, February 19, 2004 5:23 PM22
Stylistic ST5000 Series Tablet PC User’s Guide – Section Two

Table 2-1 Changing System States
* Information in Table 2-1 on page 22 is supplied to help you understand which system states your system can enter from
the current system state. Refer to the procedures on starting the system, shutting down the system, suspending system
operation, and resuming system operation given later in this chapter.

Your system may be configured to use either Suspend-to-RAM mode or Hibernate mode.
POWERING UP THE TABLET PC
Follow the procedure below to start the Stylistic ST5000
Series Tablet PC. Before you begin, confirm that the
system is in the Off state. To do so, observe the Status
display. If the Power icon is not visible in the Status
display, the system is in Off state or in Hibernate (Save-
to-Disk) mode and it is safe to perform this procedure. If
the Power icon is visible (either blinking or on continu-
ously), do not perform this procedure. See “System
States” earlier in this chapter for details on modes repre-
sented by the Power icon.
1. Ensure that the battery in your Tablet PC is
sufficiently charged, or connect an external power
source such as the AC adapter or auto adapter to
your Tablet PC.
2. Press the Power On/Suspend/Resume button to start
the system.
After performing initialization, the system starts the
operating system installed on the hard disk drive. Once
the operating system is running, you can use the system.
SHUTTING DOWN THE SYSTEM
Follow these steps to shut down and turn off your
system:
1. If system operation has been suspended, resume
system operation. See “Resuming System Opera-
tion” later in this chapter for details.
2. Save your work and close all running programs.
3. Choose Shut Down from the Windows Start menu.
4. Carry out the Shut Down command.
The system is now in the Off state.
SUSPENDING SYSTEM OPERATION
The Tablet PC allows you to suspend the system opera-
tion without closing programs or exiting the operating
system. Use this feature to conserve battery power when
a system shutdown is not practical or when the battery
needs to be changed.
Icon Appearance Current State
To Change State
*
Power icon
displayed
continuously
On State
or
Idle State
To enter the Off state, shut down the system using the Start menu on your
system.
To enter Suspend-to-RAM or Hibernate (Save-to-Disk)

state, suspend system
operation using either a hardware or software suspend.
Power icon blinking Suspend-to-
RAM

To enter the On state, resume system operation by pressing the Suspend/
Resume button.
To enter the Off state, resume system by pressing the Suspend/Resume
button, then shut down your system.
Power icon not
displayed
Off State, or,
Hibernate
(Save-to-Disk
†)

To enter the On state, start your system, or resume system operation by
pressing the Suspend/Resume button.
If you have set your system to turn power
off from the Power Options utility in the
Control Panel, the following procedure will
not be possible, since pressing the button
shuts the system down rather than
suspending it. To change your power
options, go to Start -> Settings -> Control
Panel -> Power Options.
Ocampa2_UG.book Page 22 Thursday, February 19, 2004 5:23 PM23
Using Your Stylistic ST5000
T o suspend system operation:
1. Press the Suspend/Resume button, or carry out the
Standby command from your operating system or
power management program. (If your system is
configured to suspend operation using Hibernate
(Save-to-Disk) mode, which is explained later in this
procedure, a message is displayed while data is saved
to your hard disk.)
2. The Power icon either flashes (Suspend-to-RAM) or
is not displayed (Hibernate) when system operation
is suspended, depending on how your system is
configured. At this point, programs that were
running are stopped, active data is saved, and the
system enters one of two different low-power states,
or suspend modes, as explained in the following
paragraphs.
3. Observe the Power icon in the Status display to deter-
mine which suspend mode your system is using.

Power icon is blinking: Suspend-to-RAM mode.
In this mode, active data is saved by maintaining power
to RAM while most other system components are
powered off. The Battery Gauge icon in the Status
display indicates the battery charge level.

Power icon is not displayed: Hibernate (Save-to-Disk)
mode.

In this mode, active data is stored on the hard disk
drive and power usage is reduced to the same level used
in the Off state. When the system is in Hibernate mode,
the Battery Gauge icon is not visible in the Status
display. In this mode, there is no danger of losing data
if battery power is lost.
If you have successfully performed this procedure,
system operation is now suspended. Refer to
“Resuming System Operation” later in this chapter to
resume system operation. Also, note the following with
regard to suspending system operation:

Y ou can remove the battery while the system is in
Suspend-to-RAM or Hibernate modes in order to
install a charged battery. T o prevent losing unsaved
data, wait until system operation has suspended before
you remove the battery. Note that after you remove the
battery, you have approximately five minutes to replace
it with a new battery or to plug in a power supply
before the bridge battery is depleted.

Y our system may be configured to suspend operation
automatically after a period of inactivity.

Y our system may be configured to enter Hibernate
mode automatically after a period of time in Suspend-
to-RAM mode.

The system uses a small amount of battery power when
in Suspend-to-RAM mode. Eventually, the battery will
become fully discharged.

If the battery charge drops to a Low-Battery Warning
level while the system is running, the system will beep
periodically. If this occurs, suspend system operation,
shut down the system, or attach an external power
source, such as the AC adapter, to the Tablet PC.

If the battery charge drops to a Critically Low level
while the system is running, the system is forced into a
pre-selected mode (Suspend-to-RAM or Hibernate). If
this occurs, you must either install a charged battery, or
connect an appropriate external power source such as
the AC adapter before you can resume system opera-
tion. (If the battery charge drops to a Critically Low
level while the system is in Suspend-to-RAM mode, the
system stays in Suspend-to-RAM mode until power is
restored or totally dissipated.)

Suspending system operation interrupts data commu-
nications; therefore, some programs may block the
system from suspending to prevent an interruption.

The suspend action of the Suspend/Resume button
may be disabled to prevent accidental interruption. If
this is the case, pressing the Suspend/Resume button
will not suspend system operation as described here.
(In this case, suspend mode can only be achieved using
the system software). Contact your local help desk or
reseller if your system configuration is not suitable.

If your system is equipped with a PC Card that allows
you to connect to a wired or wireless network, you may
be logged off the network after a period of inactivity
while system operation is suspended. Contact your
network administrator or help desk, or call Fujitsu
Service and Support at 1-800-8Fujitsu
(1-800-838-5487) for details on log-off parameters for
your network.
If you are replacing the battery, wait until
system operation is suspended and the
power icon is flashing before you remove
the battery. Failure to do so could result in
loss of your unsaved data. (Note that if the
Resume On LAN function is enabled in the
BIOS setup, you should not remove the
battery unless the system is shut down.
When Resume ON LAN is enabled, the
bridge battery is disabled in order to
optimize battery life.)
If you will not be using the system for an
extended period of time, shut down the
system rather than using Suspend-to-RAM
mode.
Ocampa2_UG.book Page 23 Thursday, February 19, 2004 5:23 PM24
Stylistic ST5000 Series Tablet PC User’s Guide – Section Two
RESUMING SYSTEM OPERATION
T o resume operation from either Suspend-to-RAM or
Hibernate modes, press the Suspend/Resume button.

From Suspend-to-RAM mode
Status lights indicate that the system state is changing.
It may take up to a minute before the system returns to
the On state and system operation resumes. Note that
the display turns on shortly before the pen becomes
active due to the power-up sequences observed by the
system.

From Hibernate (Save-to-Disk) mode
Active data is read from the hard disk drive, and the
system returns to the On state after a short time.
Use the system as you normally would once system oper-
ation resumes.
All programs resume at the point where execution
stopped when system operation was suspended.
ADJUSTING THE DISPLAY BRIGHTNESS
There are four ways to adjust the brightness of your
display:

Click the Tablet icon in the system tray at the bottom
right of the screen. (When the cursor is on top of the
icon, a message stating “Change tablet and pen set-
tings” is displayed.) When the Tablet and Pen Settings
window appears, select the Display tab, and move the
Screen Brightness slider to change the brightness.

Click Start -> Control Panel -> Tablet and Pen Set-
tings. Select the Display tab, and move the Screen
Brightness slider to change the brightness.

Click the Fujitsu Menu icon in the system tray at the
bottom right of the screen. (When the cursor is on top
of the icon, a message stating “Fujitsu Menu…” is dis-
played.) Select Tablet and Pen Settings and select the
Display tab. Move the Screen Brightness slider to
change the brightness.

Press the Fn key twice to invoke the Fujitsu menu and
select Tablet and Pen Settings.
USING THE PEN
Y ou can use the Stylistic ST5000 Series pen to generate
and create electronic “ink” , to select items, and to navi-
gate through programs on the Tablet PC. Programs that
support handwriting recognition also allow you to write
characters directly on the screen with the pen. Y ou can
also use the pen as a drawing tool.
Figure 2-1. Stylistic ST5000 Series Pen
The screen reacts when the pen tip is approximately 1/8
inch (3-5mm) from the screen. The pen has three
switches: a tip switch and a barrel button toggle switch
with switches at both ends. When activated, the tip
switch corresponds to the left mouse button, and the

Leave a Comment