Apple – iPhone 13 Pro Max – Repair Guide

Category: Cell Phone, Smartphone, Flip Phone, Pocket PC, and PDA User Guides and Manuals

Download user manual for Apple – iPhone 13 Pro Max – Repair Guide 
Preview: Below is a preview of the manual as extracted from the PDF file


© 2022 Apple Inc. All rights reserved.
Repair Manual
iPhone 13 Pro MaxiPhone 13 Pro Max
073-00325-A | 2 © 2022 Apple Inc. All rights reserved.
Contents
3 Introduction
Basics
6 Internal View
7 Orderable Parts
9 Screws
10 Tools
Safety
15 Battery Safety
18 Broken Glass
Procedures
20 First Steps
21 SIM Tray
22 Display
50 Bottom Speaker
54 Camera
62 Taptic Engine
67 Battery
ContentsiPhone 13 Pro Max
073-00325-A | 3 © 2022 Apple Inc. All rights reserved.
Introduction
Introduction
This manual includes technical instructions for replacing genuine Apple parts in iPhone and is intended
for individual technicians with the knowledge, experience, and tools required to repair electronic devices.
Important
• Read the entire manual first. If you’re not comfortable performing the repairs as instructed in
this manual, don’t proceed.
• Always use the latest version of this document available at support.apple.com/manuals/
repair+manual.
Warning
• Failure to follow the repair instructions or to use genuine Apple parts or proper tools may
cause fire or other safety issues and lead to personal injury or death.
• iPhone 7 and later are classified as Class 1 Laser products per IEC 60825-1 Ed. 3.
These devices comply with 21 CFR 1040.10 and 1040.11, except for conformance with
IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019. These
devices contain one or more lasers. Use other than as described in the user guide, repair,
or disassembly may cause damage, which could result in hazardous exposure to infrared
laser emissions that are not visible.
Failure to follow the repair instructions or to use genuine Apple parts or proper tools may damage
the iPhone, parts, or other property, or compromise the device’s functionality or water resistance.
Caution
Warranty information
Damage caused by repairs performed outside of Apple or the Apple Authorized Service network is not
covered by Apple’s warranty or AppleCare plans. Such damage may cause future repairs to be subject
to out-of-warranty costs or render the device ineligible for future repairs by Apple or Apple Authorized
Service Providers.iPhone 13 Pro Max
073-00325-A | 4 © 2022 Apple Inc. All rights reserved.
Introduction
Software tools
A System Configuration step may be required at the end of your repair. System Configuration
is a postrepair software tool that completes the repair for genuine Apple parts. Running System
Configuration has a number of purposes that vary based on the part replaced.

What System
Configuration
does Why it’s important
Transfers factory
calibration values
Certain parts like displays, cameras, and ambient light sensors have calibration
values that are customized to each individual part during manufacturing.
Transferring these values ensures maximum performance and quality after
a repair.
Links Secure
Element and
biometric
authentication
parts
After repair of a logic board or a biometric authentication part (Touch ID or
Face ID), linking the biometric sensors to the Secure Enclave on the logic board
is required to ensure device security.
Ensures repair
integrity
After a hardware repair, software checks are performed to ensure repair integrity.
Repair integrity means that a genuine Apple part has been correctly installed.
Assigns wireless
region
To comply with regional communications regulations, a wireless region must be
assigned to your logic board.
Updates firmware Keeping firmware up to date ensures that the device has all the latest security
and performance features.
• The heated display removal fixture softens adhesive to allow separation of the display from the
enclosure. The fixture is used with a heated display pocket designed for the device’s specific
dimensions.
• The display press applies the appropriate amount of pressure to secure new adhesive during display
installation. The display press is used with a repair tray and display adhesive press plate designed for
the device’s specific dimensions.
• The battery press applies the appropriate amount of pressure to secure new adhesive during battery
installation. The battery press is used with a repair tray designed for the device’s specific dimensions.
Ordering tools and parts
You can learn how to order genuine Apple parts and tools at support.apple.com/self-service-repair.
During the purchase process, enter the manual ID EGKCZN to indicate that you’ve read this manual
in its entirety and agree that you have the knowledge and experience to perform your intended repair.
Tools and parts
Hardware tools
Apple tools are designed to apply the appropriate heat, force, and torque during repairs, and to
withstand high-volume professional use.iPhone 13 Pro Max
073-00325-A | 5 © 2022 Apple Inc. All rights reserved.
Introduction
System Configuration requires a strong Wi-Fi network capable of 1.0 Mbps download and upload speeds,
with less than 400 ms latency and less than 2% packet loss. Estimated data usage to run
System Configuration is 6–22 MB.
The device must be running the latest version of iOS and not a beta version.
Learn how to initiate the System Configuration process at support.apple.com/self-service-repair.
Important
Supplemental information for successfully completing procedures;
neither a Warning nor a Caution
Caution Instructions for reducing risk of data loss or device hardware damage
Alerts
Failure to follow alerts could result in fire, injury, data loss, or damage to the device, parts, or other
property.
Warning Instructions for reducing risk of personal injuryiPhone 13 Pro Max
073-00325-A | 6 © 2022 Apple Inc. All rights reserved.
Internal View
Internal View
1. Top speaker
2. TrueDepth camera assembly
3. Cameras
4. Camera flex cable
5. Battery adhesive tabs
6. Battery
7. Bottom speaker
8. Lightning connector
9. Bottom microphones
10. Taptic Engine
11. Battery connector
12. SIM reader
13. Display/Multi-Touch connector
14. Logic board cowling
15. Logic board
16. Ambient light/proximity sensor connector
17. Grounding strapiPhone 13 Pro Max
073-00325-A | 7 © 2022 Apple Inc. All rights reserved.
Orderable Parts
Name Numbers Screws
Battery 661-22294 —
Bottom speaker 923-06648 923-05106 (1) lower right
923-06276 (3) lower left, upper left,
upper right
Camera 661-22293 —
Camera cowling 923-06632 923-06266 (1) middle
923-06267 (1) upper right
923-06268 (3) lower left, lower right,
left
Display 661-22309
LL661-22309 (U.S.)

Display adhesive 923-06625 —
Lower cowling 923-06641 923-06265 (3)
Rubber gasket 923-06647 —
Security screws — 923-06633 (2) graphite
923-06872 (2) silver
923-06873 (2) gold
923-06874 (2) sierra blue
923-07197 (2) alpine green
SIM tray 923-06646 dual, graphite
923-06908 single, graphite
923-06909 single, silver
923-06910 single, gold
923-06911 single, sierra blue
923-06913 dual, silver
923-06914 dual, gold
923-06915 dual, sierra blue
923-07195 dual, alpine green
923-07196 single, alpine green

Orderable PartsiPhone 13 Pro Max
073-00325-A | 8 © 2022 Apple Inc. All rights reserved.
Orderable Parts
Name Numbers Screws
Taptic Engine 923-06643 923-06263 (1) left
923-06635 (1) upper right (super
screw)
923-06636 (1) lower middle
Upper cowling 923-06639 923-06269 (1) upper left
923-06285 (2) lower left, lower right
923-06634 (1) upper rightiPhone 13 Pro Max
073-00325-A | 9 © 2022 Apple Inc. All rights reserved.
Screws
Screws
• Never reinstall a screw after it has been removed. Install only new screws. iPhone screw
grooves are covered in adhesive that can’t be reused.
• Use only the torque driver indicated to install new screws during reassembly. Both
overtightened screws and loose screws can damage parts.
Warning
923-06269
923-06285
923-06265
923-06276
923-06635
923-06263
923-06636
923-06633
923-06872
923-06873
923-06874
923-07197
923-06267
923-06634
923-06276
923-05106
923-06266
923-06268
T orque driver (black, 0.35 kgf cm)
T orque driver (blue, 0.65 kgf cm)
T orque driver (gray, 0.55 kgf cm)
T orque driver (green, 0.45 kgf cm)
Single screw
Screw with super screw underneath
Crosshead screw
Super screw
Trilobe screw
Security screw
Note: You can use any torque driver to remove screws.iPhone 13 Pro Max
073-00325-A | 10 © 2022 Apple Inc. All rights reserved.
Tools
Tools
923-01092
Adhesive cutter
923-02657
Battery press
661-08916
Display press
923-06601
Display adhesive press plate Cut-resistant gloves
923-06622
6.7-inch back protective
cover
923-06597
6.7-inch repair tray
923-04880
6.7-inch display protective
cover
661-22310
6.7-inch heated display
pocket
Tools with part numbers are available for purchase from the Self Service Repair Store. Tools without part
numbers can be purchased from electronics supply retailers.iPhone 13 Pro Max
073-00325-A | 11 © 2022 Apple Inc. All rights reserved.
Tools
ESD mat ESD-safe tweezers ESD-safe cleaning solution
ESD wrist strap with clip
or plug
Ethanol wipes
1
923-01290
Micro stix® bit
Nitrile or lint-free gloves
922-5065
Nylon probe (black stick) Safety glasses with side
shields
661-17619
Heated display removal
fixture
Heat-resistant gloves IPA wipesiPhone 13 Pro Max
073-00325-A | 12 © 2022 Apple Inc. All rights reserved.
Tools
923-00105
Torque driver (green,
0.45 kgf cm)
923-0448
Torque driver (blue,
0.65 kgf cm)
923-00738
Torque driver (gray,
0.55 kgf cm)
1
Ethanol wipes must contain at least 90% ethanol and no additives except isopropyl alcohol.
2
Clean, dry, untreated sand (8–10 cups)
3
 Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid)
4
The black torque driver kit includes a black torque driver (0.35 kgf cm), Torx® security bit (923-0247), and JCIS
bit (923-0246).
923-02066
Super screw bit Sand container
3
923-0248
Torque driver (black,
0.35 kgf cm) kit
4
Sand
2iPhone 13 Pro Max
073-00325-A | 13 © 2022 Apple Inc. All rights reserved.
Tools | Heated Display Removal Fixture
Heated Display Removal Fixture
Note: A rented heated display removal fixture may have different packaging than shown. If your fixture
came with a USB cable, set the cable aside. This setup doesn’t require it.
1. Remove the fixture from
the box. Then remove the
packing Styrofoam.
2. Cut and remove the zip tie
from the handle.
Don’t lift the fixture by
the knob.
CautioniPhone 13 Pro Max
073-00325-A | 14 © 2022 Apple Inc. All rights reserved.
Tools | Heated Display Removal Fixture
3. Turn the top knob on the
fixture counterclockwise
to raise the suction cup.
Remove the packing
Styrofoam.
4. Turn the emergency stop
knob clockwise until it
clicks and protrudes from
the stop guard.
5. Plug the power cord into the fixture. The fixture won’t turn on until you flip the switch on the back.iPhone 13 Pro Max
073-00325-A | 15 © 2022 Apple Inc. All rights reserved.
Battery Safety
Battery Safety
• Clean, dry, untreated sand (8–10 cups)
• Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid)
• Heat-resistant gloves
• Safety glasses with side shields
• ESD-safe cleaning solution
Warning
• This device contains a built-in lithium-ion rechargeable battery with soft battery cells. Battery
safety is the number one concern when repairing a device with a built-in lithium-ion battery.
• Only technicians with the knowledge, experience, and tools required to repair electronic
devices should replace a battery.
• Improper battery replacement, improper handling of parts, failure to discharge the battery
before repair, or failure to follow the provided instructions could cause battery overheating,
swelling, venting, leaking, or a battery thermal event. These events could result in fire, injury,
death, data loss, or damage to the device, parts, or other property.
• To avoid these potentially harmful events, follow the battery safety guidelines and work in
a safety-focused workspace with the tools listed below. It’s important to be prepared for all
possible outcomes.
How to set up a workspace for battery safety
Tools
Workspaces used to repair Apple devices should meet the following criteria:
• Nonflammable and electrostatic discharge (ESD)-safe work bench
• At least 2 feet away from paper and other combustible materials
• Sand container within reach (2 feet) on both sides of the workspace, not above the workspace
• Adequate ventilationiPhone 13 Pro Max
073-00325-A | 16 © 2022 Apple Inc. All rights reserved.
Battery Safety
How to handle a battery thermal event
Act immediately if you notice any of the following signs of a battery thermal event:
A battery thermal event is a rapid chemical chain reaction that occurs inside a battery cell.
The energy stored in the battery is released suddenly, which can cause outgassing and fire.
A battery thermal event can be triggered by physical damage to the battery, improper
replacement or repair, or temperatures outside the battery’s operating range.
Don’t use water or an ABC or carbon dioxide fire extinguisher on a battery thermal event or a
device that is undergoing one. Water and ABC or carbon dioxide fire extinguishers won’t stop the
reaction.
Do smother the battery or device immediately with plenty of clean, dry sand. Dump the sand
all at once. Timing is critical — the faster you pour all the sand, the sooner the reaction will
be contained.
Do contact local fire authorities if further assistance is needed.
Do leave the room for 30 minutes after the reaction is contained. Ventilate the area. Don’t return
until the area is clear of smoke.
Do wait 30 minutes before touching the device. Wear the heat-resistant gloves and safety glasses
with side shields to remove the device from the sand.
Do wipe the affected area with water first. Then wipe the area with an ESD-safe cleaning solution.
Do dispose of the damaged battery or device (including any debris removed from the sand)
according to local environmental laws and guidelines.
• The lithium-ion battery or a device that contains one begins to smoke or emit sparks or soot.
• The battery pouch suddenly and quickly puffs out.
• The lithium-ion battery or a device that contains one begins to emit hissing or popping sounds.
WarningiPhone 13 Pro Max
073-00325-A | 17 © 2022 Apple Inc. All rights reserved.
Battery Safety
• Disconnect all external cables.
• Remove all cases and covers.
• Turn on the flashlight from the Lock Screen, in Control Center, or by asking Siri. Wait until the device
has turned off and the flashlight is no longer illuminated.
How to handle batteries
The flashlight produces heat. Keep the iPhone in a well-ventilated area while the flashlight
is illuminated.
Caution
Fully discharge the battery before you begin a repair. A discharged battery is less susceptible to a
battery thermal event. If you can’t determine the battery level, don’t repair the device.
Warning
Perform the following steps to discharge the battery:
• To avoid noxious fumes or a battery thermal event, don’t puncture, strike, or crush a lithium-ion
battery or a device that contains one.
• Keep your workspace clear of foreign objects and sharp materials.
• Be careful when using sharp tools near the battery.
• Don’t leave loose screws, extra screws, or small parts inside the device.
• Don’t use tools that conduct electricity.
• Don’t throw or drop the battery.
• Don’t expose the battery to excessive heat or sunlight, or temperatures outside the battery’s
operating range.
• Handle and dispose of waste batteries in accordance with local laws and regulations.
Best practicesiPhone 13 Pro Max
073-00325-A | 18 © 2022 Apple Inc. All rights reserved.
Broken Glass
Broken Glass
Tools
Warning
iPhone displays and some back covers are made of glass. The glass could break if the iPhone is
dropped on a hard surface, receives a substantial impact, or is crushed, bent, or deformed. Don’t
attempt to remove chipped or cracked glass shards.
If the iPhone glass is broken, perform the following steps before beginning a repair:
5. Wait at least 12 minutes for the bond between the protective cover and the glass to strengthen.
6. If the back glass is broken, place the iPhone into the heated display pocket.
• Back protective cover
• Cut-resistant gloves
• Display protective cover
• Heated display pocket
• Safety glasses with side shields
• Vacuum cleaner
1. Put on safety glasses with side shields and the cut-resistant gloves.
2. Use a vacuum cleaner to remove glass pieces from your workspace and the iPhone.
3. Attach a protective cover to the broken glass to prevent injury or scattering of glass. Each protective
cover has a release liner underneath. Slowly pull the release liner out from under the protective cover
while pressing the cover onto the enclosure.
4. Fold the release liner. Use the shiny side of the release liner to firmly press the protective cover onto
the broken glass and smooth out any air bubbles.iPhone 13 Pro Max
073-00325-A | 19 © 2022 Apple Inc. All rights reserved.
Broken Glass
If the iPhone has any of the following conditions, stop the repair:
• There’s no glass or insufficient glass for the protective cover to adhere to.
• The protective cover doesn’t adhere to the iPhone.
• The iPhone doesn’t fit in the heated display pocket.
You can find a service option at support.apple.com/repair.iPhone 13 Pro Max
073-00325-A | 20 © 2022 Apple Inc. All rights reserved.
First Steps
First Steps
Always perform the following steps before starting a repair:
• Back up the iPhone.
• Discharge the battery fully.
• Turn off the iPhone.
• Disconnect all cables.
• Remove all cases and covers.
• Clear and clean your workspace.
• Put on an ESD wrist strap and attach it to a properly grounded ESD mat.
ESD (electrostatic discharge, or the release of static electricity) can damage electronic
components.
Caution
Loose screws, extra screws, or small parts inside the device can damage the battery and cause
safety issues. Set aside all parts and screws removed during the repair and account for them at
the end of the repair.
Warning
Be aware of the following while performing a repair:
• The manual for this model may show images of other models, but the procedures are the same.
Ensure that you use the correct tools for the model you’re repairing.
• Take your time. Thoroughly read all instructions and alerts.
• Magnetizing the torque drivers will make it easier to work with small screws.
• The end of each flex cable must align with its connector. Press the end of each flex cable to its
connector until it clicks to ensure that it’s secure.iPhone 13 Pro Max
073-00325-A | 21 © 2022 Apple Inc. All rights reserved.
SIM Tray
SIM Tray
• SIM-eject tool or paper clip
1. Press the SIM tray back into the side of the enclosure.
1. Find your model to locate the SIM tray.
2. Insert a paper clip or SIM-eject tool into the hole next to the SIM tray.
3. Push the paper clip or SIM-eject tool toward the enclosure to eject the SIM tray.
4. Remove the SIM tray.
Tools
Removal
Reassembly
SIM TrayiPhone 13 Pro Max
073-00325-A | 22 © 2022 Apple Inc. All rights reserved.
• 6.7-inch heated display pocket
• 6.7-inch repair tray
• Adhesive cutter
• Display adhesive press plate
• Display press
• ESD-safe tweezers
• Ethanol wipes or isopropyl alcohol
(IPA) wipes
• Heated display removal fixture
• Heat-resistant gloves
• JCIS bit
• Micro stix bit
• Nylon probe (black stick)
• Torque driver (black, 0.35 kgf cm)
• Torque driver (gray, 0.55 kgf cm)
• Torque driver (green, 0.45 kgf cm)
• Torx security bit
Display
Display | Before You Begin
Tools
• Read Battery Safety and follow workspace and battery handling guidelines before you begin.
• Read Broken Glass before you begin.
Warning
Before You BeginiPhone 13 Pro Max
073-00325-A | 23 © 2022 Apple Inc. All rights reserved.
Display | Before You Begin
Caution
• To avoid damaging the
lenses, don’t touch
the TrueDepth camera
assembly or nearby
parts.
• Don’t touch the
back of the display.
Touching the back of
the display may affect
image quality.
• This procedure requires System Configuration. After you’ve completed all removal and
reassembly steps, learn how to initiate the System Configuration process at
support.apple.com/self-service-repair.
• Read Heated Display Removal Fixture if you’re setting up the fixture for the first time.
ImportantiPhone 13 Pro Max
073-00325-A | 24 © 2022 Apple Inc. All rights reserved.
Removal
Display | Removal
1. Use a torque driver and the
Torx security bit to remove
the two security screws,
one from each side of the
Lightning connector. Set
aside the screws.
2. Flip the switch on the
back of the heated display
removal fixture to turn it on.
The internal fan will turn
on. Wait for a checkmark to
appear on the screen.
Note: If an error code
appears on the screen,
turn off the fixture and
turn it back on.iPhone 13 Pro Max
073-00325-A | 25 © 2022 Apple Inc. All rights reserved.
Display | Removal
3. Take the iPhone out of the
repair tray. Then insert the
iPhone into the heated
display pocket with the
display faceup and the
Lightning connector facing
the bottom of the pocket.
4. Flip down the clamp on the
side of the pocket to lock
the iPhone into place.
Ensure that the clamp on
the side of the pocket is
flipped up.
ImportantiPhone 13 Pro Max
073-00325-A | 26 © 2022 Apple Inc. All rights reserved.
Display | Removal
5. Put on the heat-resistant
gloves. Align the cutout on
the bottom of the pocket
with the rail on the fixture.
Slide the pocket with the
iPhone onto the rail on the
fixture.
Don’t insert the pocket
into the fixture without
wearing the heat-resistant
gloves.
WarningiPhone 13 Pro Max
073-00325-A | 27 © 2022 Apple Inc. All rights reserved.
Display | Removal
6. Slide the pocket into the
fixture until you hear the
pocket click into place.
Note: The screen on the
fixture will turn red and
the timer will count down
from 2 minutes while the
pocket heats to the correct
temperature. When the
timer ends, the fixture
will start to beep and the
screen will turn green.iPhone 13 Pro Max
073-00325-A | 28 © 2022 Apple Inc. All rights reserved.
Display | Removal
7. Turn the knob on the fixture
clockwise to lower the
suction cup as close to the
iPhone as possible without
touching the iPhone.
Caution
T o avoid damaging the
iPhone, don’t turn the knob
before the timer beeps.
Note: The fixture will beep
until the suction cup is
lowered.
8. Grasp the handle and slide
the suction cup straight out
until the edge of the suction
cup aligns with the bottom
edge of the display.
Caution
Failure to align the edges
of the suction cup and the
display may damage the
iPhone.iPhone 13 Pro Max
073-00325-A | 29 © 2022 Apple Inc. All rights reserved.
Display | Removal
9. Turn the knob on the fixture
clockwise to lower the
suction cup onto the
display (1). Then flip down
the handle on the suction
cup to secure the suction
cup to the display (2).
10. Slowly turn the knob on the
fixture counterclockwise
until the display begins to
separate from the enclosure.
If you don’t see a gap
between the display and
the enclosure immediately,
wait 30 seconds. If you
still don’t see a gap, turn
the silver part of the knob
counterclockwise until the
display begins to separate
from the enclosure.
ImportantiPhone 13 Pro Max
073-00325-A | 30 © 2022 Apple Inc. All rights reserved.
Display | Removal
11. Insert the edge of the
adhesive cutter between the
display and the enclosure.
Run the cutter between the
display and the enclosure to
the right and left as shown
until the display partially
releases from the enclosure.
Caution
To avoid damaging the
flex cables, don’t tilt up
the bottom of the display
more than 5 degrees.iPhone 13 Pro Max
073-00325-A | 31 © 2022 Apple Inc. All rights reserved.
Display | Removal
12. Flip up the handle to release
the suction cup (1). Gently
slide the flat end of the black
stick under the edge of the
suction cup to release it from
the display (2).
13. Press the eject button on
the side of the pocket to
release the pocket from
the fixture.
Don’t turn the knob.
Turning the knob may
damage the flex cables.
CautioniPhone 13 Pro Max
073-00325-A | 32 © 2022 Apple Inc. All rights reserved.
Display | Removal
14. Hold both sides of the
pocket and slide it straight
out of the fixture.
15. Flip up the clamp on the
side of the pocket to release
the iPhone (1). Hold the area
outlined in blue and gently
remove the iPhone from the
pocket (2).
16. Place the iPhone into the repair tray with the display faceup and the Lightning connector facing the
cutout. Remove the gloves.iPhone 13 Pro Max
073-00325-A | 33 © 2022 Apple Inc. All rights reserved.
Display | Removal
17. Slide the display slightly
toward the bottom of the
iPhone.
18. Insert the edge of the
adhesive cutter into the top
of the iPhone between the
display and the enclosure.
Hold the adhesive cutter at
a 45-degree angle. Start at
the middle and cut along the
top and sides of the iPhone
until the display is free.
To avoid damaging the
flex cables, don’t tilt up
the bottom of the display
more than 5 degrees.
Caution
19. Insert the repair tray suction
cups into the slots in the
repair tray. iPhone 13 Pro Max
073-00325-A | 34 © 2022 Apple Inc. All rights reserved.
20. Tilt up the display toward
the suction cups. Press the
top and bottom edges of
the display to secure it to
the suction cups.
Caution
• T o avoid damaging the
enclosure or display,
ensure that the
internal display clips
are released before
you tilt up the display.
• Don’t damage the flex
cables as you tilt up
the display.
If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service
option at support.apple.com/repair.
Warning
Display | RemovaliPhone 13 Pro Max
073-00325-A | 35 © 2022 Apple Inc. All rights reserved.
22. Use a torque driver and the
JCIS bit to remove the two
crosshead screws from the
upper cowling (3). Hold the
cowling in place while you
remove the last screw. Set
aside the screws.

23. Use ESD-safe tweezers to remove the lower cowling. Save the cowling for reassembly.
Display | Removal
21. Use a torque driver and the
Micro stix bit to remove the
three trilobe screws from
the lower cowling (1) and
the two trilobe screws from
the upper cowling (2). Set
aside the screws.
24. Use ESD-safe tweezers to tilt up the upper cowling. Then slide the cowling out from under the
ambient light sensor flex cable. Save the cowling for reassembly.
Caution
Don’t tear the ambient light sensor flex cable while removing the cowling.iPhone 13 Pro Max
073-00325-A | 36 © 2022 Apple Inc. All rights reserved.
25. Use the black stick to lift
the end of the battery flex
cable off the connector (1).
26. Use the black stick to lift
the ends of the display flex
cable (2) and ambient light
sensor flex cable (3) off the
connectors.
27. Hold the display by the edges. Pull the tabs on the suction cups to release them from the display.
Then set the display facedown on a clean, flat surface.
28. Remove the suction cups from the repair tray.
Display | Removal
Caution
You must disconnect the
battery flex cable first to
ensure that the iPhone
remains turned off.iPhone 13 Pro Max
073-00325-A | 37 © 2022 Apple Inc. All rights reserved.
Display | Removal
29. Use ESD-safe tweezers to
pick up the adhesive. Then
pull the adhesive to remove
it from the enclosure.
Repeat this process until
all the adhesive is removed
from the perimeter of the
enclosure.
Don’t touch the
TrueDepth camera
assembly, grounding
springs, or nearby parts.
Caution
31. Use ethanol wipes or IPA wipes to clean any adhesive residue from the enclosure.
30. Use ESD-safe tweezers to remove the grounding foam from the top of the enclosure above the
TrueDepth camera.
Don’t use ethanol wipes or IPA wipes on the display. Ethanol or isopropyl alcohol may damage the
display and affect image quality.
CautioniPhone 13 Pro Max
073-00325-A | 38 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
Reassembly
1. Inspect the internal display
clips for damage before
reassembly. Ensure that the
internal display clips are at a
90-degree angle and aren’t
bent or damaged.
2. Place the enclosure in the repair tray with the Lightning connector facing the cutout.
3. Inspect the TrueDepth
camera. Ensure that the
top edge of the TrueDepth
camera is under the lip of
the enclosure as shown.
If the TrueDepth camera is
positioned incorrectly, use
the black stick to move it
into the correct position.
Caution
• If the internal display clips are damaged, you may need to replace the display.
• If you’re installing a replacement display, peel the protective liner from the top and underside
of it.
Important
Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and
cause safety issues.
WarningiPhone 13 Pro Max
073-00325-A | 39 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
5. The replacement display
adhesive has a top release
liner, a middle release liner,
and a bottom release liner.
Grasp the tab on the bottom
release liner. Then slowly
pull the bottom release
liner (1) out from under the
adhesive (2) while pressing
the adhesive onto the
enclosure.
Don’t remove the top
release liner yet.
Important
4. Align the replacement display adhesive over the enclosure with the grounding foam on top. Ensure
that the top holes of the adhesive align over the TrueDepth camera assembly.
Ensure that you’ve removed all adhesive residue from the display and the enclosure before you
apply the replacement display adhesive.
Caution
Note: The replacement
display adhesive for your
model may look different
from the illustration, but the
steps are the same.
Bottom release liner
AdhesiveiPhone 13 Pro Max
073-00325-A | 40 © 2022 Apple Inc. All rights reserved.
7. Place the display adhesive
press plate on top of the
enclosure with the icon
in the top right corner as
shown.
Display | Reassembly
6. Use the flat end of the black
stick to gently adhere the
grounding foam as shown.
Failure to adhere the
grounding foam may
damage the display,
Wi-Fi, or TrueDepth
camera.
CautioniPhone 13 Pro Max
073-00325-A | 41 © 2022 Apple Inc. All rights reserved.
8. Position the repair tray with
the iPhone in the display
press. Pull down the lever
until the display press locks.
Display | ReassemblyiPhone 13 Pro Max
073-00325-A | 42 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
9. Wait until the timer on the
display press beeps. Pull
down the lever (1) and pull
out the release knob (2).
Then lift the lever (3).
10. Remove the repair tray from the display press and remove the press plate.iPhone 13 Pro Max
073-00325-A | 43 © 2022 Apple Inc. All rights reserved.
14. Press the ends of the
display flex cable (1) and
ambient light sensor flex
cable (2) to the connectors.
Press evenly along the
length of each connector.
Display | Reassembly
11. Remove the left section on
the top release liner first (1).
Then remove the three
sections running along the
right (2), top (3), and
bottom (4).
12. Insert the suction cups into the repair tray.
13. Align the left edge of the display with the left edge of the enclosure. Gently press along the edges of
the display to secure it to the suction cups.
Don’t remove the middle
release liner yet.
Important
15. Press the end of the
battery flex cable to the
connector (3). Press
evenly along the length of
the connector.
Top release liner iPhone 13 Pro Max
073-00325-A | 44 © 2022 Apple Inc. All rights reserved.
16. Use ESD-safe tweezers to
position the lower cowling
over the ends of the display
and battery flex cables.
18. Use ESD-safe tweezers to
slide the tab of the upper
cowling behind the ambient
light sensor flex cable. Then
lower the cowling over the
end of the flex cable.
17. Use the black torque driver
and Micro stix bit to install
three new trilobe screws
into the lower cowling.
19. Use the green torque driver
and JCIS bit to install two new
crosshead screws into the
upper cowling (1).
Display | Reassembly
20. Use the black torque driver
and Micro stix bit to install
two new trilobe screws into
the upper cowling (2).iPhone 13 Pro Max
073-00325-A | 45 © 2022 Apple Inc. All rights reserved.
25. Remove the suction cups from the repair tray.
24. Pull the tabs on the suction cups to release them from the display. Tilt down the display to rest on
the enclosure.
21. Peel the first strip of the
middle release liner (1)
clockwise, starting at
the bottom right of the
enclosure. Peel the second
strip of the middle release
liner (2) counterclockwise,
starting at the bottom right
of the enclosure. Then peel
the third strip (3) clockwise,
starting at the bottom left
of the enclosure.
22. Inspect the display adhesive to ensure that it’s in the correct position and not damaged or wrinkled. If
the adhesive is damaged, remove it and apply replacement adhesive.
23. Repeat step 3 to ensure that the TrueDepth camera is in the correct position. Then continue to
step 24.
Display | Reassembly
Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and
cause safety issues.
Warning
Middle release lineriPhone 13 Pro Max
073-00325-A | 46 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
26. Press all four corners of
the display simultaneously.
Then press along the edges
of the display until you hear
a click and the display is
flush with the enclosure.
Ensure that the flex
cables aren’t trapped
between the display and
the enclosure. Feel the
edges of the display for
variations or gaps. If the
display isn’t flush, repeat
all removal steps and
check the flex cables for
damage. Then repeat
reassembly steps 1
through 26.
CautioniPhone 13 Pro Max
073-00325-A | 47 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
27. Position the repair tray with
the iPhone in the display
press. Pull down the lever
until the display press locks.iPhone 13 Pro Max
073-00325-A | 48 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
28. Wait until the timer on the
display press beeps. Pull
down the lever (1) and pull
out the release knob (2).
Then lift the lever (3).
29. Remove the repair tray from the display press. iPhone 13 Pro Max
073-00325-A | 49 © 2022 Apple Inc. All rights reserved.
Display | Reassembly
30. Use the gray torque driver
and Torx security bit to
install two new security
screws, one on each side of
the Lightning connector. As
you install the screws, press
lightly on the display near
the Lightning connector.
If the screws aren’t flush,
remove and set aside the
screws. Repeat step 30 to
install another new set of
screws. If the new screws
still aren’t flush, repeat all
removal and reassembly
steps.
Caution
• System Configuration is required if you’ve installed a replacement display, battery, or camera.
Disregard notifications about iPhone features on the Lock Screen until you complete System
Configuration.
• After you’ve completed all removal and reassembly steps, learn how to initiate the System
Configuration process at support.apple.com/self-service-repair.
ImportantiPhone 13 Pro Max
073-00325-A | 50 © 2022 Apple Inc. All rights reserved.
Bottom Speaker | Before You Begin
Avoid touching the
grounding springs on the
bottom speaker.
Caution
Bottom Speaker
• 6.7-inch repair tray
• ESD-safe tweezers
• JCIS bit
• Nylon probe (black stick)
• Torque driver (blue, 0.65 kgf cm)
• Torque driver (gray, 0.55 kgf cm)
Tools
• Display
Remove the following part
before you begin:
Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Warning
Before You BeginiPhone 13 Pro Max
073-00325-A | 51 © 2022 Apple Inc. All rights reserved.
1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.
2. Use a torque driver and the
JCIS bit to remove the four
crosshead screws from the
bottom speaker. Set aside
the screws.
Removal
Bottom Speaker | Removal
3. Use ESD-safe tweezers to
grasp the lower left screw
hole and peel the bottom
speaker away from the
battery shim. Then remove
the bottom speaker from
the enclosure.iPhone 13 Pro Max
073-00325-A | 52 © 2022 Apple Inc. All rights reserved.
1. Rotate the repair tray.
Ensure that the rubber
gasket is positioned as
shown. If the gasket is out
of position, use ESD-safe
tweezers to reposition it.
3. Use the gray torque driver
and JCIS bit to install three
new crosshead screws
into the bottom speaker as
shown. Press the bottom
speaker down while you
install the screws.
2. Rotate the repair tray. Then position the bottom speaker in the enclosure.
Reassembly
Bottom Speaker | Reassembly
Don’t damage the
grounding springs on the
bottom speaker.
CautioniPhone 13 Pro Max
073-00325-A | 53 © 2022 Apple Inc. All rights reserved.
Bottom Speaker | Reassembly
4. Use the blue torque driver
and JCIS bit to install one
new crosshead screw into
the bottom speaker.
• Display
Reinstall the following part to complete reassembly:iPhone 13 Pro Max
073-00325-A | 54 © 2022 Apple Inc. All rights reserved.
• To avoid damaging
the lenses, don’t
touch the TrueDepth
camera assembly or
nearby parts.
• Avoid the grounding
spring on the camera
cowling.
Caution
Camera
• 6.7-inch repair tray
• ESD-safe tweezers
• JCIS bit
• Micro stix bit
• Nitrile or lint-free gloves
• Nylon probe (black stick)
• Torque driver (black, 0.35 kgf cm)
• Torque driver (gray, 0.55 kgf cm)
Tools
• Display
Remove the following part
before you begin:
Camera | Before You Begin
Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Warning
Before You BeginiPhone 13 Pro Max
073-00325-A | 55 © 2022 Apple Inc. All rights reserved.
Camera | Before You Begin
This procedure requires System Configuration. After you’ve completed all removal and reassembly
steps, learn how to initiate the System Configuration process at support.apple.com/self-service-
repair.
ImportantiPhone 13 Pro Max
073-00325-A | 56 © 2022 Apple Inc. All rights reserved.
1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.
2. Use a torque driver and the
Micro stix bit to remove the
four trilobe screws from the
camera cowling. Hold the
camera cowling in place
as you remove the center
screw. Set aside the screws.
3. Use a torque driver and
the JCIS bit to remove the
crosshead screw from the
camera cowling. Set aside
the screw.
Removal
Camera | RemovaliPhone 13 Pro Max
073-00325-A | 57 © 2022 Apple Inc. All rights reserved.
Camera | Removal
4. Use ESD-safe tweezers to
tilt up the camera cowling
from the left side (1). Then
slide the cowling tabs out of
the slots on the right side of
the enclosure (2). Save the
cowling for reassembly.
5. Use ESD-safe tweezers
to lift the ends of the two
camera flex cables off the
connectors. iPhone 13 Pro Max
073-00325-A | 58 © 2022 Apple Inc. All rights reserved.
6. Gently hold the camera
flex cables together (1) and
lift the cameras out of the
enclosure (2).
Camera | RemovaliPhone 13 Pro Max
073-00325-A | 59 © 2022 Apple Inc. All rights reserved.
Reassembly
Camera | Reassembly
4. Press the ends of the two
camera flex cables to the
connectors.
3. Position the cameras in the enclosure.
2. Tilt the bottom edge of the
cameras down and toward
the battery as shown.
Ensure that the camera
flex cables are inside the
channel between the battery
and the camera well.
1. Put on the gloves to prevent contamination of the camera lenses. Then hold the replacement cameras
with the lenses facedown and remove the protective cover from the camera lenses.iPhone 13 Pro Max
073-00325-A | 60 © 2022 Apple Inc. All rights reserved.
Camera | Reassembly
7 . Hold the camera cowling in
place with your finger. Then
use the black torque driver
and Micro stix bit to install
one new trilobe screw into
the middle of the cowling (1).
• Ensure that the screw cutouts in the camera cowling align with the screw holes and that the
tabs are inside the slots in the enclosure. A misaligned camera cowling may affect display
image quality.
• Ensure that the grounding spring on the camera cowling isn’t damaged. Avoid touching the
grounding spring as you reinstall the cowling.
Caution
6. The camera cowling has tabs that fit into slots on the right side of the enclosure. Hold the cowling with
ESD-safe tweezers and slide the cowling tabs into the slots. Then lower the cowling onto the cameras.
5. Lightly press the cameras into the enclosure.
8. Use the black torque
driver and Micro stix bit
to install three new trilobe
screws (2-4) into the
camera cowling.
9. Use the gray torque driver
and JCIS bit to install one
new crosshead screw into
the camera cowling (5).
• Display
Reinstall the following part to complete reassembly:
After you’ve completed all removal and reassembly steps, learn how to initiate the System
Configuration process at support.apple.com/self-service-repair.
ImportantiPhone 13 Pro Max
073-00325-A | 61 © 2022 Apple Inc. All rights reserved.
Camera | Reassembly
During System Configuration, you will perform LiDAR Scanner calibration. Prepare for calibration by
reviewing the following steps:
Note: The calibration process takes approximately 5 minutes.
1. Use a well-lit area containing
objects of different shapes
and sizes.
4. Start scanning by slowly
panning back and forth to
the left and right of the
starting point. Follow the
directions that appear on
the device screen.
2. Sit or stand 1 to 2 feet from
the objects.
3. Hold the device vertically and
rest your elbow on your body
to help stabilize your arm.iPhone 13 Pro Max
073-00325-A | 62 © 2022 Apple Inc. All rights reserved.
Taptic Engine
• 6.7-inch repair tray
• ESD-safe tweezers
• JCIS bit
• Nylon probe (black stick)
• Super screw bit
• Torque driver (blue, 0.65 kgf cm)
Tools
Taptic Engine | Before You Begin
Read Battery Safety and follow workspace and battery handling guidelines before you begin.
This procedure requires a replacement battery shim, which is available with a replacement
Taptic Engine, bottom speaker, or battery. It’s not a separate orderable part.
Warning
Important
• Display
• Bottom speaker
Remove the following
parts before you begin:
Important
Before You BeginiPhone 13 Pro Max
073-00325-A | 63 © 2022 Apple Inc. All rights reserved.
1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.
2. Use a torque driver and the
super screw bit to remove
the super screw from the
Taptic Engine. Set aside the
screw.
3. Use a torque driver and the
JCIS bit to remove the two
crosshead screws from the
Taptic Engine. Set aside the
screws.
Removal
Taptic Engine | RemovaliPhone 13 Pro Max
073-00325-A | 64 © 2022 Apple Inc. All rights reserved.
4. Lift the end of the T aptic
Engine flex cable off
the connector.
5. Use ESD-safe tweezers
to remove the Taptic
Engine with the battery
shim attached from the
enclosure.
Taptic Engine | RemovaliPhone 13 Pro Max
073-00325-A | 65 © 2022 Apple Inc. All rights reserved.
2. Use ESD-safe tweezers to
position the Taptic Engine
with battery shim in the
enclosure.
1. Remove the adhesive release liner from the replacement battery shim. Then adhere the battery shim
to the top edge of the Taptic Engine.
3. Press the end of the Taptic
Engine flex cable to the
connector.
Reassembly
Taptic Engine | ReassemblyiPhone 13 Pro Max
073-00325-A | 66 © 2022 Apple Inc. All rights reserved.
4. Use the blue torque driver
and super screw bit to install
one new super screw into
the T aptic Engine (1).
5. Use the blue torque driver
and JCIS bit to install two
new crosshead screws into
the T aptic Engine (2).
Taptic Engine | Reassembly
Reinstall the following parts to complete reassembly:
• Bottom speaker
• DisplayiPhone 13 Pro Max
073-00325-A | 67 © 2022 Apple Inc. All rights reserved.
Battery
Battery | Before You Begin
• 6.7-inch repair tray
• Battery press
• ESD-safe cleaning solution
• ESD-safe tweezers
• Ethanol wipes or isopropyl alcohol
(IPA) wipes
• Heat-resistant gloves
• Nitrile or lint-free gloves
• Nylon probe (black stick)
• Safety glasses with side shields
• Sand
• Sand container
Tools
Before You Begin
• A battery should be replaced only by individual technicians with the knowledge and experience
to repair electronic devices. Improper battery replacement, improper handling of parts, or
failure to follow the provided instructions could result in fire, injury, data loss, or damage to the
device, parts, or other property.
• Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Warning
Remove the following
parts before you begin:
Important
• Display
• Bottom speaker
• Taptic EngineiPhone 13 Pro Max
073-00325-A | 68 © 2022 Apple Inc. All rights reserved.
To avoid damaging the
lenses, don’t touch
the TrueDepth camera
assembly or nearby parts.
Caution
Battery | Before You Begin
This procedure requires System Configuration. After you’ve completed all removal and reassembly
steps, learn how to initiate the System Configuration process at support.apple.com/
self-service-repair.
ImportantiPhone 13 Pro Max
073-00325-A | 69 © 2022 Apple Inc. All rights reserved.
1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.
2. Use ESD-safe tweezers
to grasp the bottom right
battery adhesive tab. Gently
peel the adhesive tab away
from the battery.
Removal
Battery | Removal
Note: The battery has
four adhesive tabs.
Don’t scrape or puncture
the battery with the
tweezers.
WarningiPhone 13 Pro Max
073-00325-A | 70 © 2022 Apple Inc. All rights reserved.
Battery | Removal
3. Hold down the iPhone.
Use ESD-safe tweezers
to continue peeling the
adhesive tab from the
battery.
4. Keep the tweezers close
and parallel to the battery
and twist until you see
white adhesive strip on the
tweezers.
Don’t pull the tweezers
until the white adhesive is
wrapped around them.
Peel the adhesive tab
completely from the
battery before twisting it
around the tweezers.
Important
ImportantiPhone 13 Pro Max
073-00325-A | 71 © 2022 Apple Inc. All rights reserved.
Battery | Removal
6. Use ESD-safe tweezers to grasp the bottom left battery adhesive tab. Gently peel the adhesive
tab away from the battery.
7. Repeat steps 3 through 5 to remove the bottom left adhesive strip from the battery. If you remove the
entire strip, continue to step 8.
If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the
tweezers. Wrap the tab or strip around the tweezers and repeat steps 4 and 5. If you can’t see the tab
or strip, continue to step 8.
Important
8. Rotate the repair tray and put on the nitrile or lint-free gloves.
5. Pull the tweezers toward
the bottom of the iPhone
and continue to twist the
adhesive strip until you’ve
removed the entire strip.
If the battery adhesive tab
or strip breaks off and you
can still see it, attempt
to retrieve it with the
tweezers. Wrap the tab or
strip around the tweezers
and repeat steps 4 and 5.
If you can’t see the tab or
strip, continue to step 6.
Important
Don’t pull the adhesive strip
against parts or screws.
CautioniPhone 13 Pro Max
073-00325-A | 72 © 2022 Apple Inc. All rights reserved.
Battery | Removal
Battery | Removal
9. Hold down the iPhone.
Use ESD-safe tweezers
to gently peel one battery
adhesive tab from the top
of the battery. Then twist
the tweezers to wrap the
adhesive tab around them.
10. Keep the tweezers in the
channel between the
battery and the camera
cowling. Continue to slowly
twist the tweezers until
you’ve removed the entire
adhesive strip.
11. Repeat steps 9 and 10 to remove the remaining battery adhesive strip from the top of the battery. If
you remove the entire strip, continue to step 12.
If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the
tweezers. Wrap the tab or strip around the tweezers and repeat step 10. If you can’t see the tab or strip,
continue to step 12.
If the battery adhesive tab
or strip breaks off and you
can still see it, attempt
to retrieve it with the
tweezers. Wrap the tab or
strip around the tweezers
and repeat step 10. If you
can’t see the tab or strip,
continue to step 11.
Hold the tweezers close
and parallel to the battery
as you twist.
Important
Important
ImportantiPhone 13 Pro Max
073-00325-A | 73 © 2022 Apple Inc. All rights reserved.
Battery | Removal
13. Insert the flat end of the
black stick into one of the
insertion points as shown.
Ensure that the black stick is
inserted into a point where
the battery strip has been
fully removed. Don’t insert
the black stick into a point
where the battery tab or
strip is broken.
When using the black
stick to remove the battery
from the enclosure, don’t
damage the flex cables.
Don’t scrape, rip, tear, or
otherwise damage the
polyester film or other
areas. If damage occurs,
replace the iPhone.
Caution
12. If all four battery adhesive strips were fully removed, continue to step 14. If at least one strip was fully
removed, continue to step 13.
If all four strips were broken and can’t be retrieved, don’t forcibly pry the battery. Stop the repair. You
can find a service option at support.apple.com/repair.
WarningiPhone 13 Pro Max
073-00325-A | 74 © 2022 Apple Inc. All rights reserved.
15. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is
damaged, replace the iPhone.
14. Slightly lift the battery with the black stick just enough to grasp underneath the battery.
Battery | Removal
T o avoid damage, don’t press the black stick on the edge of the enclosure as you lift the battery.
Caution
If you can’t remove the battery, stop the repair. You can find a service option at
support.apple.com/repair.
WarningiPhone 13 Pro Max
073-00325-A | 75 © 2022 Apple Inc. All rights reserved.
1. Use ethanol wipes or IPA
wipes on the area shown
in blue to remove any
remaining adhesive from the
enclosure.
3. Reinstall the bottom speaker.
2. Reinstall the Taptic Engine.
Reassembly
Battery | Reassembly
Don’t use ethanol wipes
or IPA wipes on the areas
outlined in red. Ethanol
or isopropyl alcohol may
damage the polyester
film and wireless
charging unit.
Caution
Inspect the enclosure for
loose or extra screws and
small parts, which can
damage the battery and
cause safety issues.
WarningiPhone 13 Pro Max
073-00325-A | 76 © 2022 Apple Inc. All rights reserved.
4. Peel the pink release liner
from the underside of the
replacement battery.
Don’t remove the battery
protective cover from the
top of the battery yet.
Important
5. Hold the battery over
the enclosure with the
protective cover faceup.
Align the bottom of the
battery with the Taptic
Engine (1) and the left edge
with the logic board (2).
Then lower the battery into
the enclosure.
Battery | ReassemblyiPhone 13 Pro Max
073-00325-A | 77 © 2022 Apple Inc. All rights reserved.
Battery | Reassembly
6. The center of the repair
tray has two slots. Position
the repair tray and
enclosure onto the battery
press with the left slot over
the pin as shown.
7. Flip down the red lever to
lower the roller onto the
battery.iPhone 13 Pro Max
073-00325-A | 78 © 2022 Apple Inc. All rights reserved.
8. Slide the repair tray back
and forth through the
battery press three times
to adhere the battery to
the enclosure.
Battery | Reassembly
9. Flip up the red lever.iPhone 13 Pro Max
073-00325-A | 79 © 2022 Apple Inc. All rights reserved.
Battery | Reassembly
10. Position the repair tray and
enclosure onto the battery
press with the right slot over
the pin.
11. Flip down the red lever.iPhone 13 Pro Max
073-00325-A | 80 © 2022 Apple Inc. All rights reserved.
Battery | Reassembly
12. Slide the repair tray back
and forth through the
battery press three times
to adhere the battery to the
enclosure.
13. Flip up the red lever.iPhone 13 Pro Max
073-00325-A | 81 © 2022 Apple Inc. All rights reserved.
• Display
Reinstall the following part to complete reassembly:
Gently shake the iPhone. If the battery sounds loose, remove the display and the battery. Then
complete battery reassembly with another replacement battery.
Warning
After you’ve completed all removal and reassembly steps, learn how to initiate the System
Configuration process at support.apple.com/self-service-repair.
Important
Micro stix® is a registered trademark of OSG CORPORATION. Torx® is a registered trademark of Acument Intellectual Properties, LLC.
Battery | Reassembly
14. Remove the repair tray from the battery press.
15. Hold the edges of the
protective cover. Pull
the release tabs on the
protective cover to remove
the cover from the battery.
Don’t press the area over
the tab you’re releasing.
Important

Leave a Comment